How to Replace W10828351 Dryer Lint Filter on Whirlpool, Maytag & Kenmore — Step-by-Step

You're pulling clothes out of your Whirlpool dryer and notice dark streaks across your white shirts. Or maybe the dryer's making a rattling noise that wasn't there before. Nine times out of ten, these issues trace back to a cracked or warped lint filter. The W10828351 lint filter replacement fixes both problems — and as one homeowner put it: "Very easy to obtain and install."

This filter fits dozens of Whirlpool, Maytag, Kenmore, and KitchenAid dryers, including popular models like the LTE5243DQ2, LE4900XMN1, and Kenmore 11089419100. If your lint trap housing has cracked plastic or the screen's pulling away from the frame, you're dealing with the exact problem this part solves.

What You Need Before Starting

Here's the good news: this is one of the simplest dryer repairs you'll ever do. No tools required, no panels to remove. You literally just need the replacement filter.

• W10828351 lint filter (the part you're installing)
• Clean cloth or paper towel
• Your hand — that's it

Repair Time: 2 minutes
Difficulty: ● Beginner-friendly

Safety First

Unplug your dryer before starting. Even though this repair doesn't involve any electrical work, it's always safer to work on unpowered appliances. Also, never run your dryer without the lint filter installed — it creates a serious fire hazard as lint builds up inside the dryer cabinet.

Step 1: Remove the Old Lint Filter

Open your dryer door and grab the lint filter handle at the top of the drum opening. Pull straight up and out. If it's cracked or damaged, you might notice the screen separating from the plastic frame or pieces breaking off as you remove it.

Step 2: Clean the Filter Housing

Before installing the new filter, wipe down the filter cavity with a clean cloth. Remove any lint buildup, debris, or residue left behind. This is especially important if your old filter was damaged — small plastic pieces may have broken off inside the housing.

Step 3: Install the New W10828351 Filter

Take your new lint filter and slide it straight down into the filter cavity. Push until it seats completely — you'll feel it drop into place. The top handle should sit flush with the dryer opening, not stick up above the rim.

Step 4: Test the Fit

Pull the filter out and push it back in a few times to make sure it slides smoothly without binding. The screen should be taut across the frame with no gaps or warping. Close the dryer door and make sure it seals properly — a poorly seated filter can prevent the door from closing completely.

Testing After Installation

Plug your dryer back in and run a quick air-dry cycle (no heat) for five minutes. Open the door and pull out the lint filter. It should come out easily without sticking or making noise. If your dryer was leaving marks on clothes, run a load of old towels first to make sure the problem's resolved before putting in your good clothes.

Why Lint Filters Fail

The plastic frame on lint filters cracks over time from heat exposure and repeated use. You'll notice marks on clothes when the damaged filter lets lint escape back into the drum or when rough edges on cracked plastic snag fabric. The noisy symptom happens when broken pieces rattle around inside the filter housing during the tumbling cycle.

Frequently Asked Questions

Will this filter fit my Kenmore dryer?

The W10828351 fits numerous Kenmore models including 11089417800, 11089419100, 11089419110, 11088752790, 11088752793, 11088870110, and 110.887327793. Check the full compatibility list on the product page or compare your old filter's part number — this replaces 8531964, 8531967, W10812395, and 348399.

How often should I replace my dryer lint filter?

Replace it when you notice cracks in the plastic frame, the screen separating from the housing, or if your clothes are coming out with lint marks. Normal wear and tear means most filters last 5-8 years, but it varies based on usage. If you're doing 10+ loads per week, expect to replace it sooner.

Can I just clean my old filter instead of replacing it?

Not if it's physically damaged. If the plastic frame is cracked or the screen is torn, cleaning won't help — you need a new filter. However, if your filter is intact but just clogged, wash it with warm soapy water and a soft brush to remove fabric softener residue that regular lint removal misses.