How to Replace DA97-00209Z Ice Maker Fill Tube & Heater Assembly on Samsung Refrigerator — Step-by-Step
Always disconnect power and shut off water supply before beginning this repair to prevent electrical shock and water damage

Your Samsung refrigerator's ice maker has been producing hollow or misshapen ice cubes — or maybe no ice at all. The fill tube assembly is often the culprit when water doesn't flow properly into the ice mold. The DA97-00209Z is the complete fill tube and heater assembly that directs water from your supply line into the ice maker tray. When this part fails, you'll typically see partial fills, slow ice production, or complete ice-making failure on models like the RF260BEAESR and RF263TEAESR.
What You Need Before Starting
- Phillips head screwdriver
- Flathead screwdriver
- 1/4" nut driver
- Towels (for water cleanup)
- Small container (to catch residual water)
- Work gloves
Repair Time: 35-45 minutes
Difficulty: Moderate — Requires removing ice maker assembly and working in tight freezer space
Safety First
Unplug your refrigerator completely before starting this repair. You'll be working near electrical connections and water lines, so disconnecting power eliminates shock risk. Turn off the water supply to your refrigerator at the wall valve or under-sink connection. Even with the water off, expect some residual water in the lines — keep towels handy. The freezer compartment will start warming immediately, so work efficiently to minimize food thawing.
Step 1: Remove the Ice Maker Assembly
Open your freezer door and locate the ice maker unit on the left wall. You'll see two mounting screws at the top of the ice maker bracket. Remove these screws with your Phillips screwdriver. Gently pull the ice maker forward while lifting slightly — it's connected to a wiring harness at the back. Disconnect the wire harness by pressing the release tab and pulling straight out. Set the ice maker on a towel outside the freezer.
Step 2: Access the Fill Tube Behind the Ice Maker
With the ice maker removed, you'll see the white plastic fill tube protruding from the freezer wall. This tube is what delivers water to the ice maker. The DA97-00209Z assembly includes both the tube and the integral heater that prevents freeze-ups. Look for the mounting bracket that holds the tube in place — it's typically secured with one or two screws. Remove these screws and carefully note how the tube routes through the bracket.
Step 3: Disconnect the Old Fill Tube Assembly
Follow the fill tube back into the freezer wall cavity. You'll need to disconnect two connections: the water supply line (usually a compression fitting or quick-connect) and the heater's electrical plug. The electrical connector is typically a two-wire plug located inside the wall cavity. Press the release tab and pull to disconnect. For the water line, if it's a compression fitting, use your wrench to loosen the nut. If it's a quick-connect, press the collar and pull the tube out. Have your container ready — water will drip out.
Step 4: Install the New DA97-00209Z Assembly
Route the new fill tube through the mounting bracket in the same orientation as the original. Connect the heater wire plug first — you should hear it click into place. Next, connect the water supply line. If you're using a compression fitting, hand-tighten first, then give it a quarter turn with your wrench. Don't overtighten or you'll crack the plastic. Secure the mounting bracket screws to hold the tube assembly firmly against the freezer wall. The fill tube should point directly into the position where the ice maker will mount.
Step 5: Reinstall the Ice Maker and Test
Reconnect the ice maker's wiring harness — align the connector and push until it clicks. Lift the ice maker into position, aligning the mounting holes with the bracket. Install the two mounting screws and tighten snugly but don't strip the plastic. Turn your water supply back on and check for leaks around the fill tube connection. Plug in your refrigerator and activate the ice maker test cycle if your model has that feature (press and hold the test button for 3 seconds). Within 6-8 hours, you should have your first batch of properly formed ice.
Testing After Installation
After power is restored, listen for the water inlet valve to click and water to flow through the new fill tube during the first fill cycle. Check inside the freezer wall cavity for any water drips — if you see moisture, you may need to tighten the water connection slightly. Run the ice maker through 2-3 cycles and inspect the ice cubes. They should be solid, uniform, and properly shaped. If cubes are still hollow or small, you may have low water pressure (needs 20 PSI minimum) or a partially clogged water filter that needs replacement.
Frequently Asked Questions
Will this DA97-00209Z work on my RF261BEAEWW model?
Yes, the DA97-00209Z is compatible with the entire RF260 and RF261 series, including the RF261BEAEWW. This assembly fits dozens of Samsung French door models from that generation. Always verify your model number on the label inside your fridge door to confirm compatibility.
Why does the fill tube have a heater built in?
The integrated heater prevents the fill tube from freezing between ice-making cycles. Freezer air is well below freezing, and residual water in the tube would freeze solid without this heater. When frozen, water can't flow, and your ice maker stops working. The heater activates periodically to keep the tube clear — it's a critical part of reliable ice production.
Can I just replace the tube without the heater assembly?
No, the DA97-00209Z is designed as a complete assembly. The heater element is molded into the tube structure and cannot be separated. Attempting to use just the tube without the heater will result in freeze-ups and failed ice production. Samsung engineers designed this as a single unit for reliability and proper thermal management.
Place towels under the fill tube connection point before disconnecting — even with water off, residual water in the lines will drip out during removal
Need the part for this repair?
DA97-00209Z · In Stock · Ships next business day