How to Replace DA62-00914A Dual Water Inlet Valve on Samsung Refrigerators — Step-by-Step

Your Samsung refrigerator's water dispenser starts dribbling instead of flowing, or worse — the ice maker stops producing cubes altogether. The dual water inlet valve controls water flow to both the dispenser and ice maker, and when it fails, you'll notice it immediately. This DA62-00914A replacement works across dozens of Samsung models including the RF26DBUS1, RS21DANS1, and RS23DASV1 series.

What You Need Before Starting

This repair takes about 45 minutes and requires basic tools. You'll need:

• Phillips screwdriver
• Quarter-inch nut driver or socket wrench
• Needle-nose pliers
• Bucket or towels (for water catchment)
• Work gloves

Repair Time: 45-60 minutes
Difficulty: Moderate — requires accessing the back panel and working with water line connections

Safety First

Unplug your refrigerator completely before starting this repair. Turn off the water supply valve behind or beneath the unit — this is critical. You'll be disconnecting water lines, and even residual pressure can cause spills. Keep towels handy because some water will drain when you remove the old valve. Never attempt electrical work on an appliance that's still plugged in.

Step 1: Access the Water Inlet Valve Location

Pull your refrigerator away from the wall to access the back panel. The dual water inlet valve sits in the lower rear section, usually on the left side. Remove the screws securing the rear access panel using your Phillips screwdriver. Some models have a plastic cover that snaps off — use gentle pressure. You'll see the valve with two water lines coming in and two going out to the ice maker and dispenser.

Step 2: Disconnect Water Supply Lines

Locate the incoming water line — it's typically a quarter-inch copper or plastic tube. If you have a compression fitting, use your wrench to loosen the nut. For push-to-connect fittings, press the collar while pulling the tube out. Let any residual water drain into your bucket. The outgoing lines to the ice maker and dispenser disconnect the same way. Take a photo before removing anything so you remember which line goes where.

Step 3: Disconnect the Electrical Harness

The valve has a wire harness plugged into it — usually a white or black connector. Press the tab on the connector and pull straight out. Don't yank on the wires themselves. These connectors can be tight after years of use, so work it gently. If corrosion makes it stubborn, use your needle-nose pliers to grip the connector body while pressing the release tab.

Step 4: Remove the Old Valve and Mount the New One

The valve is held by a mounting bracket with two screws. Remove these with your nut driver or Phillips screwdriver depending on your model. The old valve should lift right out. Compare it to your new DA62-00914A to confirm the connections match — same number of ports in the same positions. Mount the new valve using the existing bracket and screws. Tighten firmly but don't over-torque plastic mounting tabs.

Step 5: Reconnect Everything in Reverse Order

Plug the wire harness into the new valve until you hear a click. Reconnect the incoming water supply line first, then attach the two outgoing lines to the ice maker and dispenser. Make sure compression fittings are snug and push-to-connect tubes are fully seated. Double-check your earlier photo. Replace the rear access panel and push the refrigerator back into position.

Testing After Installation

Turn the water supply back on slowly and check all connections for leaks. Plug the refrigerator back in. Press the water dispenser for 15-20 seconds to purge air from the lines — it'll sputter at first. Check the ice maker within 24 hours to confirm it's filling properly. Inspect the back panel area after a day to make sure no slow leaks developed.

Frequently Asked Questions

Will this valve work on both French door and side-by-side Samsung models?

Yes. The DA62-00914A is a dual-port valve used across Samsung's refrigerator lineup including RF26, RS21, RS23, and RM25 series models. It handles both ice maker and water dispenser functions. Check your model number against the compatibility list — this valve fits over 40 different Samsung configurations.

How do I know if the inlet valve is bad versus a clogged water filter?

If your water dispenser is slow but still works, try replacing the filter first. A bad inlet valve typically causes complete loss of water flow or a humming noise when you press the dispenser paddle. You might also hear a buzzing from the back of the fridge as the valve tries to open but can't. If the filter is new and you're still getting no water, the valve is likely the culprit.

Do I need to replace both solenoids or just the faulty one?

The DA62-00914A is a complete valve assembly with both solenoids built in — you can't replace them individually. When one solenoid fails, it's best practice to replace the entire unit anyway. The second solenoid has the same operating hours and will likely fail soon after. This saves you from doing the same repair twice in six months.