How to Replace 4391960 Dryer Heating Element on Whirlpool & Kenmore Dryers — Step-by-Step
Unplug dryer completely — 240V can be lethal. Wait 5 minutes before touching any wiring.

Your Whirlpool or Kenmore dryer's running, the drum's spinning, but your clothes come out cold and damp after an hour. That's the classic sign of a dead heating element — the most common failure point in electric dryers. If you've got a model like the LE5780XMW, 11086872100, or any of the dozens of compatible Whirlpool, Kenmore, Roper, or Estate dryers, this 4391960 heating element replacement takes about 30-45 minutes and requires nothing more than basic tools.
What You Need Before Starting
This is a straightforward repair that most people can handle with basic hand tools:
- 1/4" nut driver or socket set
- Flat-head screwdriver
- Needle-nose pliers (optional, helpful for wire terminals)
- Work gloves (the metal edges can be sharp)
- Multimeter (if you want to test the old element)
Estimated Time: 30-45 minutes
Difficulty: Easy to Moderate — requires removing the dryer cabinet but no complex disassembly
Important Note: The 4391960 element no longer ships with the two terminals and two adapter leads. If your old element's terminals are corroded or damaged, you'll need to order those separately (part numbers 279318 for terminals). Check before you start.
Safety First
Unplug the dryer from the wall outlet completely. If it's hardwired, flip the breaker at your electrical panel. Electric dryers run on 240 volts, which can kill you. Don't skip this step. Wait five minutes after unplugging to let any residual charge dissipate before touching any wiring.
Step 1: Access the Heating Element Housing
For most Whirlpool and Kenmore models, you'll need to remove the front panel. Open the dryer door and remove the two screws inside the door opening at the top. Then lift the top panel by inserting a putty knife into the clips along the front edge. Once the top's up, remove the screws securing the front panel and disconnect the door switch wire harness. Set the panel aside carefully.
Step 2: Locate and Remove the Heating Element Assembly
The heating element sits in a metal housing on the right side of the dryer (looking from the front). It's a rectangular metal box, usually about 10 inches long. You'll see two wire connections on the front and a single screw or two securing the housing bracket. Disconnect both wires — take a photo first so you remember which goes where. Remove the mounting screw and pull the entire housing straight out.
Step 3: Replace the Heating Element Coil
The housing has a metal bracket held by two screws on one end. Remove those screws and slide out the old coil. Inspect it — you'll likely see a break in the coil wire or visible burn marks. Slide the new 4391960 element into the housing in the same orientation. The coil should sit loosely but not rattle around. Reattach the end bracket with the two screws.
Step 4: Reinstall and Reconnect Everything
Slide the housing back into its mounting position and secure it with the screw. Reconnect the two wire terminals to the element — they only fit one way, but if you're reusing old terminals, make sure they're tight and not corroded. Push each wire connector on firmly until you hear a click or feel resistance. A loose connection here will cause arcing and premature failure.
Step 5: Reassemble the Dryer Cabinet
Reverse your disassembly steps. Reattach the front panel, reconnect the door switch wire, secure all screws, and lower the top panel until the clips snap back into place. Double-check that nothing's loose or left disconnected inside before closing everything up.
Testing After Installation
Plug the dryer back in and run it empty on high heat for five minutes. You should feel hot air coming from the vent within 2-3 minutes. If it's not heating, recheck your wire connections — loose terminals are the most common mistake. If it heats but smells like burning dust, that's normal for the first cycle as manufacturing oils burn off the new coil.
Frequently Asked Questions
Will this 4391960 element work on my Kenmore 110 series dryer?
Yes, if your model number starts with 110.86 or 110.76, this element fits. Check the compatibility list on the product page — it covers dozens of Kenmore models including the 11086872100, 11076990100, and 11076974610. The Whirlpool-manufactured Kenmore dryers from the 1990s through 2010s almost all use this same element.
Why doesn't the element come with wire terminals anymore?
Cost cutting and the fact that most DIYers can reuse the old terminals if they're not corroded. The terminals themselves rarely fail unless they've been arcing or exposed to moisture. Inspect your old element's terminals — if they're blackened, pitted, or loose, order new ones (part 279318). Otherwise, transfer them to the new element.
How can I tell if my heating element is actually bad before ordering?
Set your multimeter to resistance (ohms). Disconnect one wire from the element and touch the probes to both terminals. A good element reads between 8-12 ohms. Infinite resistance (no reading) means the coil's broken. Zero ohms means it's shorted to ground. If you don't have a multimeter, the no-heat symptom combined with the drum spinning normally is 95% diagnostic for a bad element.
Photograph wire connections before disconnecting anything. Transfer old terminals to new element if they're not corroded.
Need the part for this repair?
4391960 · In Stock · Ships next business day