How to Replace 137032600 Inlet Thermal Fuse on Frigidaire Electrolux Dryers — Step-by-Step

Your Frigidaire dryer drum tumbles but produces zero heat. You've checked the settings, cleaned the lint trap, and verified the breaker — everything looks normal. The culprit? Your 137032600 inlet thermal fuse has blown. This tiny component acts as a safety shutoff when your dryer's exhaust system gets too hot, and once it trips, it won't reset. You'll need to replace it.

What You Need Before Starting

This repair takes about 30-45 minutes and requires minimal tools. Here's what to gather:

• ¼-inch nut driver or socket wrench
• Flathead screwdriver
• Multimeter (to test the old fuse)
• Shop vacuum (for cleaning while you're in there)
• Replacement 137032600 thermal fuse

Difficulty: Easy — No special skills needed, just patience unscrewing panels.

Time Required: 30-45 minutes

Safety First

Unplug your dryer completely before touching anything internal. If you have a gas dryer, turn off the gas supply valve as well. Even though you're working with a low-voltage component, the dryer's heating element carries 240 volts in electric models. Don't assume unplugging alone is enough — verify there's no power with a multimeter if you're unsure.

Step 1: Access the Lower Front Panel

The 137032600 thermal fuse sits near the heating element assembly, which you'll access from the front. Open your dryer door and locate two screws at the bottom edge of the door opening — one on each side. Remove these screws with your ¼-inch nut driver. Next, lift the entire lower front panel up and away from the dryer cabinet. It's held by clips at the top, so a firm upward pull will release it. Set the panel aside.

Step 2: Locate the Thermal Fuse Assembly

Look at the heating element housing on the right side of the opening (electric models). The 137032600 thermal fuse is a small rectangular component with two wire terminals, mounted directly on the blower housing or near the heating element canister. On Electrolux models like the EIMED55IIW0 or EIMED60LSS0, it's typically attached to the blower wheel housing with a single mounting screw. Don't confuse it with the high-limit thermostat nearby — the thermal fuse is non-resettable and has only two terminals.

Step 3: Test and Remove the Old Fuse

Before removing anything, test the fuse with your multimeter set to continuity mode. Touch one probe to each terminal. A functioning fuse shows continuity (0 ohms or a beep). No continuity? It's blown — that's why your dryer won't heat. Disconnect both wire terminals by pulling them straight off. Remove the mounting screw holding the fuse to the housing. While you're here, use your shop vacuum to clean out any lint buildup around the blower and heating element. Excessive lint is usually what caused the fuse to blow in the first place.

Step 4: Install the New 137032600 Fuse

Position your new thermal fuse exactly where the old one sat. The orientation doesn't matter since it's just a thermal switch, but make sure it sits flat against the mounting surface for proper heat sensing. Secure it with the mounting screw — snug but not overtightened. Push the wire terminals onto the new fuse's spade connectors until they click firmly into place. Give each wire a gentle tug to confirm they're seated.

Step 5: Reassemble and Test

Reattach the lower front panel by hooking the top clips first, then pushing the bottom into place. Reinstall the two screws inside the door opening. Plug your dryer back in (or turn the gas back on). Run a timed dry cycle on high heat with a few damp towels. Within 5-10 minutes, you should feel hot air coming from the exhaust vent. If it's heating properly, you're done.

Why Did the Thermal Fuse Blow?

Thermal fuses don't fail randomly — they trip because of restricted airflow. Check your exhaust vent system from the dryer to the outside vent hood. A kinked duct, bird's nest in the exterior vent, or years of lint buildup will cause the dryer to overheat and blow the fuse again. Clean your entire vent system before putting the dryer back into regular service, or you'll be replacing this fuse again in a few months.

Frequently Asked Questions

Will my dryer work at all if the thermal fuse is blown?

It depends on your model. Most Frigidaire and Electrolux dryers will still run and tumble with a blown thermal fuse, but they won't produce any heat. Some newer models won't start at all when the thermal fuse trips — it's a safety interlock. Either way, the fuse must be replaced; it can't be reset.

Can I bypass the thermal fuse temporarily to test my dryer?

Technically yes, but absolutely don't. The thermal fuse exists to prevent fires. If airflow is restricted enough to blow the fuse, running without it could ignite lint buildup inside your dryer. Always replace the fuse and fix the underlying airflow problem before running your dryer again.

Is part 137032600 the same as 137060800?

Yes, 137032600 replaces the older 137060800 part number. They're functionally identical and mount the same way. If your service manual lists 137060800 or AP4368739, the 137032600 thermal fuse is the correct replacement for your Frigidaire, Electrolux, Kenmore, or Gibson dryer.