How to Replace DC97-14486A Heating Element Assembly on Samsung Dryer — Step-by-Step
Unplug dryer completely and wait 10 minutes before starting. Electric heating elements operate at 240 volts. For gas dryers, turn off gas supply valve before working on the unit.

Your Samsung dryer's running through cycles, but your clothes come out cold and damp. You've checked the lint trap, inspected the vent hose, and still nothing. That's the DC97-14486A heating element assembly calling it quits — one of the most common failures in models like the DV42H5000EW/A3, DVE50M7450W/A3, and DV48H7400EW/A2.
What You Need Before Starting
This is a straightforward repair, but you'll need the right tools and about an hour of your time:
- 1/4-inch nut driver or socket set
- Phillips head screwdriver
- Flathead screwdriver (for panel clips)
- Work gloves (the element housing has sharp edges)
- Multimeter (optional, for testing the old element)
Repair Time: 45-60 minutes
Difficulty: Moderate — You'll need to remove the dryer's front or rear panel depending on your model.
Safety First
Unplug your dryer completely before starting. If you have a gas dryer, turn off the gas supply valve as well. The heating element operates at 240 volts on electric models, and there's no room for shortcuts here. Wait at least 10 minutes after unplugging to let any residual charge dissipate. Also, be aware that the element housing retains heat for a while after use — if you just ran a cycle, give it time to cool down.
Step 1: Access the Heating Element Assembly
Most Samsung dryers store the heating element in the rear panel area. Rotate your dryer so you can access the back panel easily. Remove the screws securing the rear access panel — typically 6-8 screws around the perimeter. Keep these in a container because they're easy to lose. Once the panel's off, you'll see the large cylindrical heating element housing on the lower right side (some models have it on the left).
Step 2: Disconnect Wiring and Remove Old Element
You'll see two or three wire connectors attached to the heating element terminals. Take a photo with your phone before disconnecting anything — this'll save you confusion during reassembly. Pull the connectors straight off (don't yank the wires themselves). The DC97-14486A assembly is held in place by two mounting screws or brackets. Remove these fasteners and carefully slide the entire housing out. It's bulkier than you'd expect, so support it as you pull.
Step 3: Inspect and Compare
Before installing the new DC97-14486A, look at your old element. You might see a visible break in the heating coil, or it might look fine externally but be electrically open. If you have a multimeter, check for continuity across the terminals — you should get a reading between 10-50 ohms. No reading? That's your smoking gun. Compare the mounting bracket positions on your old element with the new one to make sure everything lines up.
Step 4: Install the New DC97-14486A Assembly
Slide the new heating element assembly into the housing area, aligning the mounting holes with the bracket positions. Thread in the mounting screws and tighten them securely — but don't overtighten, as the housing is relatively thin metal. Reconnect the wire terminals in the same configuration as your photo. They should click or seat firmly. Give each wire a gentle tug to confirm it's secure.
Step 5: Reassemble and Test
Replace the rear access panel and secure all screws. Rotate your dryer back into position, plug it in (and turn the gas back on if applicable), and run a test cycle. Set it to high heat with no load or just a couple of towels. Within 5-10 minutes, you should feel hot air coming from the vent. Open the door briefly during the cycle — the drum should be noticeably warm to the touch.
Testing After Installation
Run a full cycle with a normal load of damp laundry. Your clothes should come out completely dry and warm. If you're still not getting heat, double-check your wire connections and make sure the thermal fuse (a separate component near the element) didn't blow. A blown thermal fuse is sometimes the cause of heating failures, and it won't reset — you'd need to replace that too. Also verify your home's 240V circuit breaker didn't trip during installation.
Frequently Asked Questions
Will the DC97-14486A work on Kenmore dryers made by Samsung?
Yes, this element fits Kenmore Elite dryers manufactured by Samsung, typically model numbers starting with 796. Check the compatible models list on the product page to confirm your specific model number. The part numbers DC97-14486D and DC97-08891A are direct equivalents that Samsung replaced with this updated assembly.
How long does a Samsung dryer heating element typically last?
Under normal use, expect 8-12 years. But if you're running constant loads, have restricted airflow from a clogged vent, or frequently overload the dryer, the element works harder and fails sooner. Always keep your lint trap and external vent clean — that's the number one way to extend element life.
Can I test the old element to confirm it's actually bad?
Absolutely. Set your multimeter to the lowest ohms setting and touch the probes to the element's terminals. A good element reads between 10-50 ohms. An open circuit (infinite resistance or no reading) means the coil's broken. If you get a reading but the dryer still doesn't heat, check the thermal fuse, cycling thermostat, and high-limit thermostat — those are the other usual suspects in the heating circuit.
Take a photo of the wire connections before disconnecting them. This simple step will save you troubleshooting time during reassembly and ensure you reconnect everything correctly.
Need the part for this repair?
DC97-14486A · In Stock · Ships next business day