How to Replace DG47-00038B Oven Bake Element on Samsung Range — Step-by-Step

Your Samsung oven's stuck at 200°F when you've got it cranked to 425°F, and that casserole dish is just sitting there, lukewarm. This is the classic sign of a dead bake element — and on models like the NE59J3421SS, NE59M4310SS, or NE59T4311SS, replacing the DG47-00038B element fixes the problem in about 30 minutes.

The bake element is that coiled heating component at the bottom of your oven cavity. When it fails, you'll get little to no heat when baking — sometimes the element won't heat at all. I've seen these go out after 5-7 years of regular use, especially if you bake frequently or run self-clean cycles often.

What You Need Before Starting

Tools required:

• 1/4-inch nut driver or socket set
• Flathead screwdriver
• Work gloves (element edges can be sharp)
• Flashlight or headlamp

Repair time: 25-35 minutes
Difficulty: Easy

You don't need to be a professional to handle this. If you can turn a screwdriver and follow simple steps, you're good to go.

Safety First

Warning: Disconnect power at the circuit breaker before starting this repair. Not just pulling the plug — actually flip the breaker. Electric ranges pull serious amperage, and you're working directly with heating element terminals. Double-check that the oven is completely cold before touching anything inside.

Step 1: Access the Bake Element

Open your oven door fully and remove all the racks. You'll see the bake element at the bottom — it's the exposed coil that wraps around in a horseshoe or rectangular shape. Look at the back wall where the element connects. You'll spot two screws holding a metal bracket that secures the element terminals.

Step 2: Remove the Mounting Screws

Use your 1/4-inch nut driver to remove the two screws securing the element bracket. On most Samsung models, these are located about 2 inches from the bottom of the back wall. Once the screws are out, gently pull the element forward about 3-4 inches. Don't yank it — the wires are still connected behind the back panel.

Step 3: Disconnect the Wire Terminals

Now you can see the two wire terminals plugged onto the element prongs. These are slip-on connectors — just pull them straight off. If they're stuck from heat cycling, wiggle them gently side to side while pulling. Take a quick photo with your phone before disconnecting so you remember which wire goes where (though they're usually the same, it's a good habit).

Step 4: Install the New DG47-00038B Element

Line up your new element's terminal prongs with the wire connectors and push them on firmly. You should feel them click into place. Feed the element back through the mounting holes in the rear oven wall. The element should sit flat against the bottom of the oven cavity — if it's twisted or sitting at an angle, pull it back out and reposition it.

Step 5: Secure and Test

Thread the two mounting screws back through the bracket and tighten them down. Don't overtighten — snug is fine. Replace your oven racks, close the door, and flip the breaker back on. Set your oven to 350°F and watch through the window. The element should start glowing red within 2-3 minutes. Let it run for 10 minutes to verify it heats evenly across the entire coil.

Testing After Installation

Run a full preheat cycle to 425°F with an oven thermometer on the center rack. Your Samsung should hit target temp in 12-15 minutes. If it's taking longer or you're still seeing uneven heating, double-check that both wire terminals are fully seated on the element prongs. A loose connection will cause weak or intermittent heating.

Frequently Asked Questions

Will this element work on both electric coil and slide-in Samsung ranges?

Yes, the DG47-00038B fits multiple Samsung configurations including freestanding models like the NE59J3420SS and slide-in models like the NE59M4320SB. Check your model number against the compatibility list to confirm — it covers most 5.9 cu ft Samsung ranges manufactured after 2015.

How do I know if it's the bake element and not the broil element?

If your oven won't heat when set to Bake but the broiler works fine, it's definitely the bottom bake element. If neither works, you might have a control board or thermal fuse issue. The bake element is the one at the bottom of the oven cavity; the broil element is at the top.

Can I test the old element to confirm it's bad before ordering?

Absolutely. Set your multimeter to resistance mode and touch the probes to each terminal prong on the element. A good element reads 15-30 ohms. If you get no reading (infinite resistance) or the reading jumps around, the element's burned out internally and needs replacement.