How to Replace 3051163 Rear Drawer Glide on Frigidaire Ranges — Step-by-Step

Your Frigidaire range drawer won't close all the way anymore. You push it in, and it either bounces back out or sits crooked, leaving a gap that bugs you every time you walk past the stove. That's the rear drawer glide — the plastic track that supports the back of your storage or warming drawer — and it's failed. The good news? This is one of the easiest range repairs you'll do.

What You Need Before Starting

This repair requires almost no tools, and you'll be done in under 15 minutes. Here's what to grab:

• Phillips screwdriver (for some models)
• Flathead screwdriver (optional, for prying clips)
• Work gloves (metal edges can be sharp)

Repair Time: 10-15 minutes
Difficulty: EASY

Part 3051163 fits a wide range of Frigidaire, Electrolux, and Kenmore ranges including FEF365ASL, FEF366BCA, FEF336BGDA, MEF322WBSE, and FGF354BGWC models. Check your model number on the label inside the storage drawer or on the frame behind it.

Safety First

You don't need to disconnect power for this repair since you're not touching any electrical components. However, make sure the range is cool if you've used it recently. Remove everything from the storage drawer before you start — pans, baking sheets, whatever's in there. You'll need the drawer completely empty and pulled out.

Step 1: Remove the Storage Drawer Completely

Pull the drawer out about halfway, then lift the front up at a 45-degree angle while pulling forward. The drawer should lift off the glides. If it doesn't budge, look for release tabs on the metal glide rails — press them in while lifting. Set the drawer aside where it won't get stepped on.

Step 2: Locate the Failed Rear Glide

Look at the floor of the range cavity where the drawer sits. At the back center, you'll see the rear glide — it's a white or cream-colored plastic piece about 4 inches long that the back of the drawer slides on. If yours is cracked, broken, or missing chunks, that's why your drawer won't close properly. The drawer back literally has nothing solid to rest on.

Step 3: Remove the Old Glide

Most rear glides either snap into place or have one or two screws holding them. Check the ends of the glide for screw heads — if you see them, remove them with a Phillips screwdriver. If there are no screws, the glide snaps into brackets. Gently pry up on one end with a flathead screwdriver or just pull firmly upward. It should pop out of the mounting clips.

Step 4: Install the New 3051163 Glide

Line up the new glide with the mounting holes or clips where the old one sat. If your model uses screws, insert them and tighten — but don't overtighten, you'll crack the plastic. If it's a snap-in design, press down firmly on both ends until you hear or feel the clips engage. Give it a tug to make sure it's seated completely. The glide should be level and centered.

Step 5: Reinstall the Drawer and Test

Align the drawer with the side glide rails, tilt the front up slightly, and slide it back onto the tracks. Lower the front and push the drawer all the way closed. It should glide smoothly now and sit flush with the range front. Open and close it a few times — you'll immediately notice the difference. No more fighting with it.

Testing After Installation

Push the drawer closed from different angles to make sure it doesn't hang up on one side. The drawer should close completely with light pressure and stay closed. Load it up with a few pans and test again — the rear glide should support the weight without flexing or popping out. If the drawer still feels wobbly, check that your side glides aren't also worn out.

Frequently Asked Questions

Will this fix a drawer that won't stay closed?

Yes, if the rear glide is broken. When the back of the drawer has no support, it tips backward and won't latch properly. A new glide levels everything out. However, if your side glides are also damaged, you'll need to replace those too for a complete fix.

How long does the rear drawer glide typically last?

These plastic glides usually last 5-10 years depending on how often you use the drawer and how much weight you load into it. Overloading with cast iron or stacking too many heavy pans accelerates wear. Once the plastic cracks, it's done — there's no temporary fix that works.

Do I need the exact part number 3051163, or will other glides work?

Stick with 3051163 or its direct replacements (AP2121518, PS434227). Generic or wrong-model glides won't fit the mounting points correctly, and you'll end up with the same crooked drawer problem. This part is inexpensive enough that using the correct one is worth it.