Maintenance

How to Extend Your Whirlpool Washer Lid Strike Life — Maintenance Guide

4 min read
May 26, 2026
Extends element life 2–3x
Avg element lifespan
8–10 years
With proper care
12–15 years
Most common damage
Stress fractures from lid slamming, detergent and mineral buildup causing poor engagement, worn catch surfaces preventing clean latching
Maintenance schedule
After each use
Close lid gently
Don't slam the lid shut. Lower it gently to reduce impact stress on the strike mechanism. This single habit will double the part's lifespan.
Monthly
Wipe down strike area
Use a damp cloth to remove detergent residue and lint from the strike and surrounding area. Check for any white powder or sticky buildup — remove it immediately with a cloth dampened with white vinegar if needed.
Every 3 months
Deep clean and inspect
Unplug washer, remove the two mounting screws, take out the strike, and clean thoroughly with warm soapy water. Inspect for cracks or wear. Clean the mounting area on the washer cabinet. Reinstall with screws snug but not overtightened.

Unplug washer before inspecting or cleaning the lid strike. Never force a stuck lid — it can break both the strike and the lid lock mechanism.

After-each-use checklist
Strike catches lid smoothly on first close
Should engage without needing to re-close the lid
No visible cracks or white stress lines in plastic
Inspect from multiple angles, especially around screw holes
Strike doesn't wiggle when pushed
Should be completely solid — any movement means loose screws or cracked posts
Catch surface is textured, not smooth/shiny
Worn smooth surface won't grip the lock mechanism properly
No detergent buildup or residue on strike
Clean white powder or sticky film immediately
Mounting screws are snug but not overtightened
Should be firm but not stripping the plastic — about 15-20 inch-pounds of torque
Signs your element needs replacement
W10837741 W10837741 Washer Lid Strike Compatible with Whirlpool Maytag Kenmore Amana Crosley, Replaces W10714899 AP5988753 PS11726338 4338531

Most Whirlpool washer lid strikes like the W10837741 should last 8-10 years, but I've seen them fail in under three when they're repeatedly slammed or exposed to detergent buildup. This little plastic catch — the piece that holds your lid closed during the spin cycle — takes more abuse than you'd think.

If you've got a WTW5000DW1, WTW4955HW0, or any of the compatible Maytag models like the MVWC565FW1, spending two minutes every few months on this part will save you from that frustrating mid-cycle lid error.

How Long Should It Last?

Under normal conditions, the W10837741 lid strike should give you 8-10 years of reliable service. I've installed replacements on washers that are over a decade old where this was the original part.

What kills it early? Three things:

  • Slamming the lid repeatedly — creates stress fractures in the plastic housing
  • Detergent and fabric softener residue — builds up around the strike mechanism, preventing clean engagement
  • Hard water deposits — similar to detergent buildup, but harder and more abrasive

With basic maintenance, you can push this to 12-15 years easily. The plastic is durable ABS — it'll outlast most other washer components if you keep it clean.

Signs It's Wearing Out

The lid strike doesn't give you much warning before it fails completely. Here's what to watch for:

Lid Won't Latch on First Try

You close the lid, press start, and nothing happens. You lift it and close it again — now it works. That's the strike not engaging cleanly with the lid lock mechanism. Could be buildup, or the catch surface is wearing smooth.

Washer Stops Mid-Cycle with Lid Error

The control panel shows an error code (usually LF or F5 E2 on Whirlpool models), and the washer won't spin. The strike isn't maintaining consistent contact with the lock. On models like the WTW4850HW0 or MVWC465HW3, this happens when the plastic catch develops hairline cracks.

Visible Cracks or White Stress Lines

Look at the strike from the side. If you see white lines radiating from the mounting holes or around the catch mechanism, that's stress fracturing. It'll fail soon — usually within a few weeks of those lines appearing.

Strike Feels Loose or Wiggles

The W10837741 should be rock-solid when installed. If it moves at all when you push on it, either the mounting screws have loosened or the screw posts inside the plastic have cracked. Don't overtighten trying to fix this — you'll make it worse.

When to Replace vs Maintain

Here's the honest truth: if the strike is cracked, just replace it. It's an $18.99 part, and trying to glue or reinforce plastic that's already failed never holds up to the vibration and force of a spin cycle.

Maintain it when:

  • It's working fine but has detergent buildup
  • The latch is sticky but not cracked
  • You're doing preventive care on a newer washer

Replace it when:

  • You see any cracks, even hairline ones
  • The catch surface is worn smooth and shiny
  • It's loose no matter how you adjust the screws
  • You're getting lid error codes consistently

Don't waste time on a failing strike. On models like the 7MWTW1700EM0 or WTW4816FW2, replacement takes five minutes with just a Torx driver.

Frequently Asked Questions

Can I use WD-40 or other lubricants on the lid strike?

No. Lubricants attract lint and detergent residue, which creates a gunky buildup that'll cause the strike to fail faster. The mechanism doesn't need lubrication — it needs to stay clean and dry. If it's sticking, that's a sign of buildup or wear, not lack of lubrication.

How do I know if my lid error is the strike or the lock mechanism?

Close the lid and look at where the lock engages the strike. If the strike looks clean and undamaged but the lid still won't lock, the problem is likely the lid lock assembly itself. If you see buildup, damage, or misalignment on the strike, start there — it's cheaper and easier to replace than the lock.

Will this part work on my Kenmore washer if it has a different model number format?

Kenmore models that start with 110.xxx are typically made by Whirlpool. The W10837741 works on Kenmore washers manufactured by Whirlpool, but you'll need to verify compatibility by your full model number. Check the compatible models list on the product page or look up your Kenmore model to see who manufactured it.

Element showing wear?

W10837741 · Replace before it fully fails

Shop W10837741 →
Replacement parts
W10837741
W10837741 Washer Lid Strike Compatible with Whirlpool Maytag Kenmore Amana Crosley, Replaces W10714899 AP5988753 PS11726338 4338531
$13.99
Add to Cart