How to Replace W10837741 Washer Lid Strike on Whirlpool Maytag Washer — Step-by-Step
Always unplug the washer before beginning any repair work, even simple ones like replacing the lid strike.

Your Whirlpool washer won't start because the lid won't latch. You close it, hear nothing, and the control panel just sits there blinking at you. Nine times out of ten, it's not the lid lock itself — it's the little plastic striker that the lock catches onto. The W10837741 lid strike wears down over time, especially on models like the WTW5000DW2 and MVWC565FW1 that see heavy family use.
This plastic component takes constant impact every time you close the lid, and after a few years, it either cracks or wears smooth enough that the lock mechanism can't detect it. The good news? It's one of the easiest washer repairs you'll ever do.
What You Need Before Starting
- Phillips head screwdriver
- Flathead screwdriver (optional, for prying)
- New W10837741 lid strike
- Work gloves (optional)
Estimated Time: 5-10 minutes
Difficulty: EASY
Safety First
Unplug your washer from the wall outlet before starting. Even though this repair doesn't involve electrical components directly, you'll be working near the lid lock mechanism, and it's better to be safe. If your washer is hard-wired, flip the circuit breaker. You don't need to disconnect water lines for this job.
Step 1: Access the Top Panel
Open the washer lid completely. Look at the rear edge of the top panel where it meets the back of the washer. You'll see two or three Phillips screws holding the top down. Remove these screws and set them aside. On models like the WTW4816FW2 and 7MWTW1700EM0, there are typically two screws, while some Maytag models have three.
Step 2: Lift and Prop the Top Panel
Once the screws are out, tilt the top panel back. It hinges from the front, so you'll lift from the rear and prop it against the wall. Some people use a stick or broom handle to hold it open, but leaning it back at about 70 degrees usually works fine. You now have clear access to the lid strike mounted on the underside of the lid.
Step 3: Remove the Old Lid Strike
The old W10837741 strike is held in place by two Phillips screws. Remove both screws and pull the strike straight down. If it's cracked or broken, pieces might fall out — that's normal. Check the mounting area for any debris or plastic fragments and wipe it clean. The strike sits in a recessed area on the underside of the lid, and you want a clean surface for the new one.
Step 4: Install the New W10837741 Strike
Position the new strike in the same location where the old one sat. The strike has a specific orientation — the wider, rounded end should face toward the front of the washer. Line up the screw holes and insert both Phillips screws. Tighten them firmly, but don't overtighten. You're threading into plastic, and you just need it snug enough that the strike doesn't shift when the lid closes.
Step 5: Lower the Top Panel and Test
Lower the washer top panel back into position. Replace the rear screws and tighten them down. Plug the washer back in (or flip the breaker), then close the lid and see if the lock engages. You should hear a distinct click, and the control panel should recognize that the lid is closed. Run a quick rinse cycle to confirm everything's working properly.
Testing After Installation
Close the lid firmly and listen for the lock mechanism to engage. On models like the MVWC465HW0 and WTW4955HW1, you'll hear an audible click within two seconds. The control panel should show that it's ready to start a cycle. If the washer still won't recognize a closed lid, check that the strike is positioned correctly — it needs to align perfectly with the lock mechanism on the washer frame. Sometimes the strike can be rotated 180 degrees by mistake, which puts the catch point in the wrong spot.
Frequently Asked Questions
Will this fix my washer if it's stuck on lid lock error?
If the error is caused by a worn or broken strike, yes. However, if the lid lock actuator itself has failed (the part that actually does the locking), you'll need to replace that component instead. The strike is just the piece the lock catches onto. A good test: if the old strike looks cracked, worn smooth, or broken, replacing it will likely solve your problem. If the strike looks fine, the lock mechanism itself might be faulty.
Is the W10837741 the same as W10714899?
Yes, W10837741 replaces W10714899, AP5988753, PS11726338, and part number 4338531. They're all the same part with different manufacturing revisions. Whirlpool updated the part number, but they're functionally identical and will fit the same washer models including Whirlpool, Maytag, Kenmore, Amana, and Crosley top-load washers.
Why does this part wear out so quickly?
It's plastic taking repeated impact every time you close the lid. On a washer that runs five or six loads per week, that's 250-300 impacts per year. The strike gets hit by the metal lock mechanism with enough force to ensure a secure connection, and over time, that plastic either develops stress cracks or wears smooth. Washers with heavier lids or families that slam the lid shut tend to go through these strikes faster. Three to five years is typical lifespan for this part.
Check the strike orientation carefully — the rounded end faces the front of the washer. Installing it backwards will prevent the lid lock from engaging.
Need the part for this repair?
W10837741 · In Stock · Ships next business day