How to Replace DC97-02250G Drain Hose Assembly on Samsung Washer — Step-by-Step

Water pooling behind your Samsung washer after every cycle? If you've noticed your WF1804WPC or WF8802RSW1 leaving puddles on the laundry room floor, there's a good chance your drain hose assembly has cracked or pulled loose from its connections. The DC97-02250G drain hose is what carries all that dirty water from your machine to your home's drain system, and when it fails, you'll know immediately.

What You Need Before Starting

This repair is straightforward once you access the hose connections. Here's what to grab:

• Flathead screwdriver
• Phillips head screwdriver
• Pliers (needle-nose work best)
• Towels (for water cleanup)
• Bucket or shallow pan
• Work gloves

Estimated time: 30-45 minutes
Difficulty: Easy

Safety First

Unplug your washer completely before starting — don't just rely on turning it off. Water will drain from the old hose when you disconnect it, so have towels ready and expect a mess. If your washer's been leaking for a while, check the floor underneath for any water damage that needs addressing separately.

Step 1: Pull the Washer Away From the Wall

You need access to the back panel. Unplug the power cord and turn off the water supply valves. Disconnect the inlet hoses — water will drip out, so have that towel handy. Pull the machine forward about two feet. This gives you room to work without contorting yourself behind a tight space.

Step 2: Remove the Back Access Panel

Most Samsung front-loaders like the WF756UMSAWQ have a rear panel held by 6-8 screws around the perimeter. Remove these with your Phillips screwdriver and set the panel aside. You'll immediately see the drain pump and hose assembly at the bottom corner. The DC97-02250G connects from the tub outlet down to the drain pump.

Step 3: Disconnect the Old Drain Hose

The hose is secured with spring clamps at both ends. Use your pliers to squeeze and slide these clamps back away from the connection points. Position your bucket underneath before you pull the hose free — residual water in the system will drain out. Wiggle the hose gently to break it loose from the pump outlet and tub connection. On models like the WF8750LSW1, there's also a support bracket midway that you'll need to unhook.

Step 4: Install the New DC97-02250G Hose

Route the new hose along the same path as the old one. Connect it to the tub outlet first — push it on firmly until it seats completely. Slide the spring clamp into position about half an inch from the end of the hose. Then connect the lower end to the drain pump outlet and secure that clamp. Make sure the hose isn't kinked or twisted anywhere along its length. Reattach any support clips or brackets you removed.

Step 5: Reassemble and Test

Replace the back panel and secure all screws. Push the washer back into position, but don't push it all the way to the wall yet. Reconnect the water inlet hoses and plug in the power. Run a quick rinse cycle while you watch the back of the machine. Check both hose connections for any drips or leaks. If everything stays dry, you're done — push the washer back and clean up.

Testing After Installation

Don't just run one cycle and call it good. Run a full wash cycle with a load of laundry, then check behind the machine again. Look at the floor, the hose connections, and the drain pump area. If you see water, you likely didn't get the clamps positioned correctly — they need to be tight against the connection points. Also verify your washer is draining completely and not leaving water in the drum after the spin cycle ends.

Frequently Asked Questions

Will this DC97-02250G hose work on my WF1752WPC model?

Yes, this hose fits a wide range of Samsung front-load washers including the WF1752WPC, WF1752WPW, WF0754W7V1, and dozens of other models. Check the compatible models list to verify your exact model number, but if your original part number matches DC97-02250G, AP6038829, or PS9496744, you're good to go.

Why does my drain hose keep failing?

Drain hoses crack over time from constant exposure to hot water and detergent chemicals. They also fail if the washer vibrates excessively or if someone accidentally kicks or pinches the hose behind the machine. If you're replacing this hose for the second time, check that your washer is level and that nothing's putting pressure on the hose routing.

Can I use a generic drain hose instead of the DC97-02250G?

Not recommended. Generic hoses often don't match the exact routing, length, or connection angles that Samsung engineered for your specific model. The DC97-02250G is molded with specific bends and lengths for models like the WD856UHSAWQ and WD8122CVB. A generic hose might fit the connections but kink along the way, causing drainage problems or another leak down the road.