Repair Guide Moderate

How to Replace 4681EA1007A Drain Pump Motor Assembly on LG Washer — Step-by-Step

6 min read
May 25, 2026
Repair time
30-45 minutes
Difficulty
Moderate
Part cost
$64.99
Tools needed
7
1Tools you'll need
Phillips screwdriver
flat-head screwdriver
needle-nose pliers
towels
shallow pan
work gloves
flashlight
2Disconnect power

Always unplug the washer before beginning repairs. Residual water will drain from the pump housing and hoses — have towels and a pan ready to catch spills.

3Step-by-step
4681EA1007A 4681EA1007A Washer Drain Pump Motor Assembly Compatible with LG Kenmore, Replaces AP5672914 PS7785119 2649379 EAP7785119

Your LG washer finished the wash cycle, but now it's just sitting there with a tub full of soapy water. The timer's done, the machine's silent, but nothing's draining. You crack open the door and water sloshes out onto your laundry room floor. This is the classic sign of a failed drain pump motor assembly — and the 4681EA1007A is the direct replacement that'll get your WT1201CW, WT4870CW, or WT5001CW back to draining properly.

What You Need Before Starting

This is a straightforward repair that most people can handle with basic tools. Here's what you'll need:

  • Phillips screwdriver
  • Flat-head screwdriver
  • Needle-nose pliers
  • Towels and a shallow pan (to catch water)
  • Work gloves
  • Flashlight or headlamp

Estimated Repair Time: 30-45 minutes

Difficulty Level: Moderate

Safety First

Unplug your washer completely before you start — don't just turn off the circuit breaker, physically disconnect the power cord. If your washer has any water still in the tub, run a drain and spin cycle first (or manually drain using the emergency drain tube if the pump is completely dead). You'll still get some water spillage when you remove the old pump, so have those towels ready. Wear gloves because the pump area can have sharp edges and accumulated debris.

Step 1: Access the Drain Pump

For most LG front-load washers like the WT1201CV and WT7200CW, the drain pump sits behind the lower front access panel. Use your flat-head screwdriver to pop off the small access door at the bottom front of the machine — it usually snaps off with gentle prying. On some models, you might need to remove a few screws first. Behind this panel, you'll see the drain pump filter housing and the pump itself. Place your shallow pan and towels underneath because residual water will come out.

Step 2: Remove the Old Drain Pump

Unscrew the large drain filter cap counterclockwise and let any remaining water drain into your pan. Now you'll see the pump housing. Disconnect the wire harness from the pump motor by pressing the locking tab and pulling straight off. Use your needle-nose pliers to squeeze and slide the hose clamps back on both the inlet and outlet hoses. Pull the hoses off — more water will come out, so have those towels positioned. Remove the mounting screws (usually 2-3) that hold the pump assembly to the washer housing, then carefully twist and pull the entire pump assembly out.

Step 3: Install the New 4681EA1007A Pump Assembly

Before installing the new pump, check the hose connections for any cracks or debris buildup. Clean the connection points with a damp cloth. Position your new 4681EA1007A pump assembly into the mounting bracket and secure it with the screws you removed earlier. Don't overtighten — snug is enough. The pump should sit flush against the housing with no gaps.

Step 4: Reconnect Hoses and Electrical

Push the inlet and outlet hoses firmly onto the new pump's ports. Slide the hose clamps back into position about 1/2 inch from the end of each hose connection. Give each hose a firm tug to make sure it's seated properly — you don't want a leak on the first drain cycle. Plug the wire harness back onto the pump motor until you hear it click into place. Thread the drain filter back into its housing and tighten it clockwise until it's snug.

Step 5: Test the Repair

Snap the front access panel back into place. Plug your washer back in and run a quick rinse and spin cycle with no clothes inside. Watch the lower front area for any water leaks during the drain cycle. Listen for the pump motor — it should hum smoothly without grinding or squealing noises. The water should drain completely within 2-3 minutes. If everything looks and sounds good, you're back in business.

Testing After Installation

After your initial test cycle completes, check the area around the pump one more time for moisture. Run a full normal wash cycle with a small load to verify the pump handles a typical amount of water without issues. The washer should transition smoothly from wash to drain to spin without any pauses or error codes. If you're working on a Kenmore model like the 79631513210, also check that the control panel isn't displaying any drain error codes (usually "OE" or "LE").

Frequently Asked Questions

Will this pump work on both LG and Kenmore washers?

Yes, the 4681EA1007A replaces the drain pump on specific LG and Kenmore front-load washers. It's compatible with models like the WT1101CW, WT4970CW, WT5270CW, and Kenmore 79631513210. Always verify your model number matches the compatibility list before ordering.

How do I know if my pump is bad or if it's just clogged?

First, remove and clean the drain filter — sometimes coins, socks, or debris block drainage without actually damaging the pump. If the filter is clear and the washer still won't drain, try the spin cycle while listening closely. A working pump makes a steady humming sound. A bad pump either stays silent, makes a grinding noise, or hums but doesn't move water. If there's no sound at all, test the pump with a multimeter — it should show continuity across the motor terminals.

Can I replace just the motor part instead of the whole assembly?

While some aftermarket sellers offer just the motor, LG designs the 4681EA1007A as a complete assembly for a reason. The pump housing, impeller, and motor are calibrated to work together. Replacing the entire assembly ensures proper fit and performance. Trying to replace just the motor often leads to leaks or poor drainage because the housing seals wear out over time too. For a repair that lasts, replace the whole unit.

This replacement part (4681EA1007A) also replaces part numbers AP5672914, PS7785119, 2649379, and EAP7785119. If your parts diagram lists any of those numbers, this is the correct replacement.

Before installing the new pump, clean any lint or debris from the hose connections. A clean connection prevents leaks and ensures the pump runs at full efficiency.

Need the part for this repair?

4681EA1007A · In Stock · Ships next business day

Shop 4681EA1007A →
Parts for this repair
4681EA1007A
4681EA1007A Washer Drain Pump Motor Assembly Compatible with LG Kenmore, Replaces AP5672914 PS7785119 2649379 EAP7785119
$64.99
Add to Cart