How to Replace 3406105 Dryer Door Switch on Whirlpool & Kenmore — Step-by-Step
Always unplug the dryer before replacing the door switch. Test that the dryer stops running when you open the door after installation.

Your Whirlpool dryer just keeps running even when you open the door, or worse — it won't start at all no matter how many times you slam the door shut. If you're dealing with a LER4634PQ0, LER3622HQ0, or any of the dozens of compatible models, you're likely looking at a failed door switch. The 3406105 door switch assembly is the part that tells your dryer when the door is closed and it's safe to operate. When it fails, your dryer either refuses to start or becomes a safety hazard by running with the door wide open.
What You Need Before Starting
This is one of the quickest dryer repairs you'll ever do. Here's what you need:
- Screwdriver (Phillips or flat-head, depending on your model)
- New 3406105 door switch assembly
- 10 minutes of your time
Repair time: Less than 15 minutes
Difficulty: Easy — Perfect first repair if you've never worked on appliances before
Safety First
Unplug your dryer from the wall outlet before you touch anything. Even though you're working on a simple switch, you don't want the drum suddenly deciding to spin while your hand is inside. If your dryer is hardwired instead of plugged in, flip the breaker at your electrical panel. Don't skip this step — it takes five seconds and prevents a trip to the emergency room.
Step 1: Access the Door Switch
Open your dryer door fully. Look at the door frame opening — you'll see the door switch mounted inside the cabinet, usually on the top or side of the door frame. It's a small rectangular or square component with two wire connectors attached. On models like the CEDX463RQ0 and CGDX463RQ0, it's typically on the right side near the top. You don't need to remove any panels for this repair, which is why it's so quick.
Step 2: Remove the Old Door Switch
You'll see one or two screws holding the switch in place. Remove these screws and set them aside where they won't roll away. The old switch will pull straight out once the screws are gone. Don't yank on it — gently pull the wire connectors off the switch terminals. They're usually push-on connectors that slide off with light pressure. If they're stubborn, wiggle them side to side while pulling.
Step 3: Install the New 3406105 Switch
Take your new switch out of the package. Push the wire connectors onto the new switch terminals — they only go on one way, so you can't mess this up. Make sure they're fully seated and won't pull off easily. Position the switch in the mounting hole and secure it with the screws you removed earlier. Don't overtighten — snug is enough. The plastic housing can crack if you hulk out on it.
Step 4: Test the Door Switch Function
Here's where you make sure everything works. Plug the dryer back in or flip the breaker. Close the door and try to start a cycle. The dryer should fire right up. Now open the door while it's running — the drum should stop immediately. If it keeps spinning with the door open, double-check that your wire connections are fully seated. This is a safety feature, so don't skip testing it.
Testing After Installation
Run a complete dry cycle to verify everything's working properly. Listen for any unusual clicking sounds from the door area — there shouldn't be any. The door should close smoothly without extra resistance. Open and close it several times to make sure the switch activates consistently. As one customer said: "Got what I needed and fixed my dryer" — that's exactly how this repair should go.
Frequently Asked Questions
Why won't my dryer start even after replacing the door switch?
If your dryer still won't start after installing the new 3406105 switch, check that the wire connectors are pushed on all the way. Sometimes they look connected but aren't making solid contact. Also verify you plugged the dryer back in — sounds obvious, but it happens. If the connections are good and you have power, you might have a separate issue like a blown thermal fuse or bad start switch.
Can I use 3406105 to replace part numbers 3406104 or WP3406105?
Yes, the 3406105 replaces WP3406105, 3406104, AP6008560, and PS11741700. They're all the same switch with different manufacturer part numbers. Whirlpool, Kenmore, Maytag, and Roper dryers all use this same component, so you're covered across brands. If your old switch has any of those numbers stamped on it, the 3406105 is your replacement.
What causes dryer door switches to fail?
The door switch gets activated thousands of times over the dryer's life — every single time you open and close the door. The internal contacts eventually wear out and stop making a solid connection. Sometimes the little plastic actuator that gets pressed by the door breaks off. High humidity in laundry rooms can also corrode the electrical contacts over time. It's a normal wear item that typically lasts 5-10 years depending on how often you do laundry.
Take a photo of the wire connections before removing the old switch. Makes reconnecting the new one foolproof, especially if the wires are the same color.
Need the part for this repair?
3406105 · In Stock · Ships next business day