How to Replace 240337901 Refrigerator Door Shelf Bin on Frigidaire — Step-by-Step

You hear that crash in the kitchen and instantly know — someone yanked too hard on a milk jug and the fridge door shelf just gave up. If you've got a Frigidaire, Electrolux, Gibson, or Kenmore fridge with a broken door bin where one of those plastic locking tabs finally snapped off, you're looking at part 240337901. One customer put it perfectly: "For some reason my son does not know how to remove items from the shelf without breaking a locking tab and having the shelf fall." Sound familiar?

The good news? This is literally a snap-in replacement. No screws, no tools, no drama. You'll spend more time driving to pick up the part than actually installing it.

What You Need Before Starting

Tools Required: None — your hands are enough

Repair Time: Less than 15 minutes

Difficulty Level: Easy

This replacement works on dozens of models including FRT18S6AWA, FRT21IL4FW3, FFHT1826LW8, LFHT2117LW8, GLRT183TDW8, and GLRT212IDW5. It replaces part numbers AP2115858, 240337904, 240337905, and PS429868.

Safety First

You don't need to unplug the fridge for this repair, but do empty the broken shelf completely before attempting removal. Plastic tabs can be sharp when broken, so watch your fingers. If the old shelf is cracked badly, have a trash bag ready because pieces might fall when you remove it.

Step 1: Remove Everything From the Door Shelf

Take out all bottles, condiments, and anything else stored in the broken bin. This seems obvious, but you'd be surprised how many people try to work around a half-full shelf. Check underneath too — sometimes small items slide under and wedge the shelf in place.

Step 2: Locate the Locking Tabs

Look at both ends of the shelf where it connects to the door. You'll see plastic tabs (or what's left of them) that hook into slots on the door liner. These tabs are the usual failure point — they crack from repeated stress when people pull items straight out instead of lifting them.

Step 3: Release the Old Shelf

Gently flex the shelf toward you while lifting up at the same time. If one side is already broken, start with the intact side. The shelf should unhook from the door slots with minimal force. If it's stuck, don't force it — check for any remaining tabs that are still engaged. Some models have upper and lower mounting points, so you might need to lift the whole shelf upward first before pulling it away from the door.

Step 4: Install the New 240337901 Shelf

Line up the new shelf with the door slots. You'll see exactly where it goes because the mounting points are molded into the door. Press the shelf tabs into the slots — you should hear or feel them click into place. As one satisfied customer noted: "I took the new shelf and snapped it in to the door." That's literally all there is to it. Test both sides to make sure they're fully seated by gently pulling on each end.

Step 5: Load Test the Installation

Don't just assume it's secure. Put a couple of heavier items back on the shelf and open/close the door a few times. The shelf should feel solid with no flexing or popping sounds. If you notice any movement, remove the shelf and reseat it — sometimes one side clicks in while the other doesn't fully engage.

Testing After Installation

Load the shelf gradually, starting with lighter items. Test the door's closing mechanism — a properly installed shelf won't interfere with the door seal. Open and close the door a few times to make sure nothing shifts. If you hear clicking or notice the shelf moving, remove and reinstall it. The locking tabs should hold firmly without any play.

Why This Part Fails (And How to Prevent It)

Here's the thing about door shelves: the plastic tabs break because people grab bottles and pull straight out with force. The shelf isn't designed for that kind of lateral stress. Teach everyone in your household to lift items up slightly while pulling them out — it takes the pressure off those locking tabs. Also, don't overload the shelf beyond its weight capacity. That gallon of milk might fit, but it's putting constant stress on those mounting points.

Frequently Asked Questions

Will this shelf fit my specific Frigidaire model?

Part 240337901 fits over 50 different Frigidaire, Electrolux, Gibson, and Kenmore models including the FRT and FFHT series. Check your model number against the compatibility list or look at your existing shelf — if the part number matches 240337904, 240337905, AP2115858, or PS429868, this is your replacement.

Can I use super glue to fix the broken tabs instead of replacing?

Don't bother. We've seen people try this, and it never holds up. The constant opening and closing of the door, plus the weight of items on the shelf, will break any glue repair within days. A new shelf costs $31.99 and takes 10 minutes to install — it's not worth the frustration of a failed repair.

Do I need to remove the door to replace this shelf?

No. The shelf snaps in and out from inside the fridge with the door in place. You're literally just pressing plastic tabs into slots. Multiple users confirm it's a straightforward snap-in installation that requires no disassembly.