How to Replace 154701001 Dishwasher Splash Shield Kit on Frigidaire — Step-by-Step

Water pooling under your Frigidaire dishwasher? If you're seeing leaks coming from the bottom front of the door, there's a good chance your splash shield has failed. One user described their fix perfectly: "Removed door front, removed bottom door gasket, installed new, a little hard to get it to catch in place but got it. Replaced door gasket and splash guards. Replaced door front. No more leaks." That's exactly what we'll walk through today.

The 154701001 splash shield kit works with most Frigidaire, Electrolux, and Kenmore dishwashers. It replaces part numbers AP4338941, PS2203346, 154685101, and 1465007. This kit typically includes both the splash shield and door gasket — everything you need to stop those annoying leaks.

What You Need Before Starting

This repair takes about 30-60 minutes and rates as "A Bit Difficult" mainly because you'll need to disassemble the door panel. Here's what to grab:

• Phillips head screwdriver
• Flathead screwdriver
• Towel (to catch any residual water)
• Replacement 154701001 splash shield kit

Difficulty: A Bit Difficult | Time: 30-60 minutes

Safety First

Unplug your dishwasher or flip the breaker before starting. Even though you're working on the door assembly, it's best practice to kill the power. You'll also want to remove the bottom rack so you have clear access to the door area. Place a towel on the floor — there's usually some trapped water that'll drip out when you remove the old gasket.

Step 1: Remove the Door From the Hinges

Open your dishwasher door about 45 degrees. Look at both side hinges — you'll see screws or clips holding the door to the tub. Remove these fasteners on both sides. Have someone help you support the door weight, or carefully lower it onto a padded surface. This prevents damage to the door or your floor.

Step 2: Take Apart the Door Panel

With the door removed, you'll see screws around the perimeter holding the inner and outer door panels together. Remove all these screws — there are usually 8-12 of them. Carefully separate the panels. The control panel might still be connected, so don't pull too hard. You just need enough separation to access the bottom gasket area.

Step 3: Remove the Old Bottom Gasket and Splash Shield

Peel away the old bottom door gasket — it's the rubber seal running along the bottom edge. Then locate the splash shield, which sits just behind this gasket area. It might be clipped or tucked into place. Remove any retaining clips if present. Note how everything sits before removal — taking a quick photo helps during reassembly.

Step 4: Install the New Splash Shield and Gasket

Position the new splash shield where the old one sat. Here's where it gets tricky — as one user mentioned, it's "a little hard to get it to catch in place." You need to work the shield into its channel carefully. Start at one end and work your way across, making sure it's fully seated. Then install the new bottom gasket by pressing it firmly into the gasket channel along the bottom door edge. It should snap into place all around.

Step 5: Reassemble and Reinstall the Door

Bring the inner and outer door panels back together. Replace all the screws around the perimeter, tightening them evenly. Don't overtighten — you can crack the plastic. Once the door is reassembled, lift it back into position and reattach it to the hinges. Secure the hinge screws on both sides.

Testing After Installation

Close the door and restore power. Run a short rinse cycle and watch the bottom door area for leaks. Check underneath the dishwasher too. If you installed everything correctly, you shouldn't see any water escaping. The gasket creates a watertight seal, and the splash shield redirects any internal spray back into the tub where it belongs.

Frequently Asked Questions

Do I really need to remove the door from the hinges?

Yes. While some repairs can be done with the door attached, replacing the splash shield requires full access to the door panel assembly. You can't get to the shield without separating the inner and outer panels, and that's much easier with the door off the dishwasher.

Will this kit work on my Kenmore dishwasher made by Frigidaire?

Most likely, yes. Many Kenmore dishwashers were manufactured by Frigidaire, and they share the same parts. Check your model number against the compatibility list, but the 154701001 fits models from Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, and Westinghouse. It replaces several part numbers including 154685101 and 1465007.

How do I know if my leak is from a bad splash shield versus something else?

Splash shield leaks show up at the bottom front of the door, usually during or right after a wash cycle. If water pools on the floor directly under the door, that's your clue. Leaks from the sides or back typically indicate different problems — maybe a faulty door latch, worn side gaskets, or a cracked tub. The location tells you a lot.