Repair Guide Easy

How to Replace 131763310 Washer Door Strike on Frigidaire Front-Load Washers — Step-by-Step

4 min read
May 22, 2026
Repair time
Less than 15 minutes
Difficulty
Easy
Part cost
$0.00
Tools needed
2
1Tools you'll need
Phillips head screwdriver
Flathead screwdriver (optional)
2Disconnect power

Unplug the washer before beginning any repair work to prevent electrical shock.

3Step-by-step
131763310 131763310 Washer Door Strike Compatible with Frigidaire Kenmore Crosley Gibson Westinghouse Electrolux, Replaces AP3580441 PS890617 131763300 1032664

You pull the washer door closed and hear... nothing. No click. No engagement. The door bounces back open, and your washer refuses to start because it doesn't think the door is latched. Nine times out of ten, it's not the latch mechanism on the door itself — it's the door strike mounted to the washer frame that's cracked or worn out.

The 131763310 door strike is that small plastic keeper on the front panel that catches the door latch assembly. After years of slamming doors and wear from laundry cycles, the strike wears down or breaks entirely. Models like the FAFW3801LW0, ATF6000FS2, and GLTF2940FS1 all use this same part, and the fix takes under fifteen minutes.

What You Need Before Starting

Tools required:

  • Phillips head screwdriver
  • Flathead screwdriver (optional, for prying)

Repair time: Less than 15 minutes
Difficulty: EASY

This is one of the simplest washer repairs you can tackle. No need to move the machine or disassemble major components.

Safety First

Unplug your washer before starting any repair work. Even though this repair doesn't involve internal electrical components, it's good practice to disconnect power whenever you're working on an appliance. Make sure the door is fully open and won't swing closed during the repair.

Step 1: Locate the Failed Door Strike

Open the washer door completely. Look at the front panel of the washer opening — not the door itself, but the cabinet frame. You'll see a small plastic piece, usually white or gray, mounted to the frame where the door latch catches when closed. That's your door strike. Check it for cracks, wear grooves, or missing chunks of plastic.

Step 2: Remove the Old Door Strike

The door strike is held in place by two Phillips head screws. Remove both screws completely and set them aside — you'll reuse them. Pull the old strike straight out from the frame. If it's stuck, gently wiggle it or use a flathead screwdriver to pry the edges, but it should slide out easily once the screws are removed.

Step 3: Position the New 131763310 Strike

Take your new door strike and align it with the mounting holes in the washer frame. The strike has a specific orientation — the curved catch side should face toward where the door closes. Push it into position until it sits flush against the cabinet opening.

Step 4: Secure the Strike with Screws

Thread both mounting screws back through the strike and into the frame. Tighten them firmly with your Phillips screwdriver, but don't overtighten — you're threading into plastic mounting points, and stripping them means bigger headaches. The strike should be solid and not wiggle when you test it with your finger.

Step 5: Test the Door Latch Engagement

Before you plug the washer back in, close the door slowly and listen for a solid click. The door latch should catch cleanly on the new strike and hold the door firmly closed. Open and close it several times to make sure the engagement is consistent. If the door still won't catch, check that the strike is oriented correctly and seated all the way into the frame.

Testing After Installation

Plug your washer back in and run a quick rinse cycle. The washer should recognize the door is closed and start filling normally. If you were getting "door open" error codes before, they should be gone. The door should seal properly during the wash cycle with no water leaks around the gasket.

Frequently Asked Questions

Why does the door strike break on Frigidaire washers?

Constant impact from closing the door wears down the plastic over time. If you have kids who slam the door or you've been forcing it closed to get the washer to start, the strike takes the brunt of that force. It's a wear part designed to fail before more expensive components get damaged.

Will this fix a door that won't stay closed during the spin cycle?

If the door pops open during spin or you hear clicking sounds, yes — a worn strike is likely the problem. The latch can't engage deep enough to trigger the door lock mechanism. Replacing the strike gives the latch something solid to catch on again.

Can I use this part on Kenmore and Electrolux washers?

Absolutely. The 131763310 is a direct replacement for Frigidaire, Kenmore, Crosley, Gibson, Westinghouse, and Electrolux front-load washers that use this strike design. It replaces part numbers AP3580441, PS890617, and 131763300. Check your model number against the compatibility list to confirm, but if your old strike looks identical, you're good to go.

Test the door engagement several times before running a cycle — a properly installed strike should click firmly every time the door closes.

Need the part for this repair?

131763310 · In Stock · Ships next business day

Shop 131763310 →
Parts for this repair
131763310
131763310 Washer Door Strike Compatible with Frigidaire Kenmore Crosley Gibson Westinghouse Electrolux, Replaces AP3580441 PS890617 131763300 1032664
$0.00
Add to Cart