Troubleshooting

Whirlpool Dryer Not Heating — 5 Causes & How to Fix It

8 min read
May 23, 2026
Multiple root causes covered
Most common cause
Failed heating element
Avg repair cost
$35–$180
DIY difficulty
Moderate
Symptom checklist
No heat production
Dryer runs and tumbles but produces no warm air
Clothes stay damp
Full cycle completes but laundry remains wet and cold
Cool air only
Air circulation present but no temperature increase
Extended dry times
Previously normal cycles now take multiple runs
No burning smell
Confirms heating circuit failure vs. electrical short
Root cause analysis
4391960 4391960 Dryer Heating Element Compatible with Whirlpool Kenmore Roper Estate, Replaces WP4391960 AP6009347 PS11742505 279218 696579

You toss a load of wet towels into your Whirlpool or Kenmore dryer, hit start, and come back 60 minutes later to find everything still damp and cold. The drum's spinning fine, but there's zero heat. This is one of the most common dryer failures, and the good news? It's usually something you can diagnose yourself in about 20 minutes.

Before you assume the heating element is toast, let's walk through the actual troubleshooting sequence. I've repaired hundreds of Whirlpool dryers (models like the LE5780XMW, LE3300XPW, and various Kenmore 110-series units), and the "no heat" complaint follows a pretty predictable pattern.

Quick Symptom Check

Confirm you're dealing with a heating issue and not something else:

  • Drum spins normally — motor and belt are fine
  • No heat at all — not even lukewarm air
  • No burning smell — that's a different problem
  • Lint screen is clean — airflow isn't restricted
  • Vent hose isn't kinked — back of dryer has proper clearance

If your dryer matches this profile, you're looking at an electrical heating circuit problem.

Cause #1: Failed Heating Element (Most Common — 45% Probability)

The heating element itself burns out over time. On Whirlpool and Kenmore dryers using element 4391960, this coil sits in a metal housing at the bottom or rear of the cabinet. When it fails, it usually breaks somewhere along the coiled wire.

How to test it:

  1. Unplug the dryer — seriously, don't skip this
  2. Remove the lower front panel or rear panel (depends on your model)
  3. Locate the heating element canister — it's a rectangular metal box
  4. Disconnect the wire terminals and use a multimeter set to resistance (ohms)
  5. Touch probes to the element terminals — you should read 8–12 ohms
  6. If you read infinite resistance (OL on digital meters), the element's broken

Replacement element 4391960 runs about $33.99. Important note: Newer versions of this element no longer include the two wire terminals and adapter leads — you'll need to order those separately if your old element had them attached.

Cause #2: Blown Thermal Fuse (30% Probability)

The thermal fuse is a one-time safety device that cuts power to the heating element if the dryer overheats. It's usually mounted on the blower housing or near the heating element canister. Once it blows, it stays blown — there's no reset button.

Why it blows: Restricted airflow. That means clogged lint screens, packed vent hoses, or birds nesting in your exterior vent.

Testing procedure:

  1. Locate the thermal fuse (small oval component with two wires)
  2. Disconnect both wires
  3. Test continuity with your multimeter
  4. A good fuse reads 0 ohms (complete circuit)
  5. A blown fuse reads infinite resistance

Here's the thing: replacing a blown thermal fuse without fixing the airflow problem means it'll just blow again in a few weeks. Clean your entire vent system before you button everything back up.

Cause #3: Defective Cycling Thermostat (15% Probability)

The cycling thermostat (sometimes called the operating thermostat) regulates the heating element's temperature. It opens and closes to maintain the temperature you selected. When it fails in the open position, the element never gets power.

These thermostats are mounted on the blower housing, usually held by two screws. They're round, about the size of a quarter, with two wire terminals. Test for continuity at room temperature — you should have a closed circuit. If it reads open (infinite resistance) at room temp, it's bad.

Cause #4: Bad High-Limit Thermostat (8% Probability)

Similar to the thermal fuse, the high-limit thermostat cuts power if temps get too high. Unlike the fuse, it's supposed to reset when things cool down. But they stick open sometimes, especially after years of heat cycling.

It's typically mounted directly on the heating element housing. Test it the same way as the cycling thermostat — should show continuity at room temperature.

Cause #5: Faulty Timer or Control Board (2% Probability)

Least likely, but I've seen it. The timer or electronic control board sends power signals to the heating circuit. If those controls fail, the element never gets the signal to turn on. This is a diagnosis of elimination — if you've tested everything else and it all checks out, you're looking at a control problem.

Testing this properly requires a wiring diagram for your specific model and some electrical troubleshooting skills. This is usually when I tell people to call a tech.

The DIY Repair Sequence

Here's the order I follow:

  1. Check the obvious stuff first — circuit breaker, lint screen, vent hose
  2. Test the thermal fuse — easiest component to access and test
  3. Test the heating element — second most common failure
  4. Check both thermostats — if you're already in there with the multimeter
  5. Verify voltage at the element — make sure power's actually arriving

For models like the LE6605XPW1, EL2020WW, or Kenmore 11086872100, the element replacement is pretty straightforward. Budget about 45 minutes if it's your first time, 20 minutes once you've done it before.

When to Call a Pro

If you've tested the element, both thermostats, and the fuse — and they all check out fine — you're looking at a wiring or control board issue. That's when it makes sense to bring in a tech with a wiring diagram and proper testing equipment.

Also, if you're not comfortable working with the dryer unplugged, discharging capacitors (on some models), or pulling panels off, there's no shame in hiring it out. A dryer repair usually runs $150–$250 depending on your area.

Frequently Asked Questions

Why does my Whirlpool dryer run but produce no heat at all?

Most commonly, either the heating element has burned out or the thermal fuse has blown. Both are safety-related failures. The element fails from normal wear after thousands of cycles. The thermal fuse blows when airflow restriction causes overheating — usually from a clogged vent system. Test both components with a multimeter to confirm which one failed.

Can I run my dryer if the heating element is broken?

Yes, the dryer will run and tumble clothes normally, it just won't produce any heat. You'll end up with damp laundry after a full cycle. There's no safety issue with running it this way short-term, but obviously it's not doing its job. The motor and drum mechanism work independently from the heating circuit.

Do I need special tools to replace a Whirlpool dryer heating element?

Not really. A 1/4-inch nut driver or socket set, a Phillips screwdriver, and a multimeter for testing are all you need. Some models require a Torx driver for certain screws. The actual element (part 4391960) just slides out of its housing once you disconnect the wires and remove a mounting screw or two. The trickiest part is usually getting the panel off to access it.

Diagnosed the problem?

4391960 · In Stock · Fast shipping

Shop 4391960 →
Likely parts needed
4391960
4391960 Dryer Heating Element Compatible with Whirlpool Kenmore Roper Estate, Replaces WP4391960 AP6009347 PS11742505 279218 696579
$24.99
Add to Cart