How to Replace 4027EL1001A Dryer Door Latch Assembly on LG & Kenmore Dryers — Step-by-Step
Unplug dryer completely before starting repair to avoid electrical shock

Your LG dryer's running, but the door won't stay shut. You push it closed, hear a faint click, and the moment you let go — pop — it swings open again. Or worse, the door feels secure but your dryer won't start because the latch assembly has worn out and can't signal the control board that it's actually closed. This is exactly what happens when the 4027EL1001A door latch assembly fails, and it's one of the most common fixes on models like the DLEX3570W, DLE2512W, and DLEX2801R.
What You Need Before Starting
This is a straightforward mechanical replacement that doesn't require specialized tools:
- Phillips screwdriver
- Flathead screwdriver (for prying trim panels)
- Work gloves (optional, for handling sharp metal edges)
Estimated Time: 15-20 minutes
Difficulty: Easy
Safety First
Unplug your dryer completely before starting. Even though this repair doesn't involve direct electrical connections, you'll be working near wiring harnesses inside the door frame. If your dryer is gas-powered, you don't need to shut off the gas line for this repair — the latch assembly is purely mechanical and mounts to the door itself.
Step 1: Access the Door's Inner Panel
Open the dryer door fully. Look along the inner edge where the door seal meets the frame — you'll see 4-6 Phillips screws holding the inner door panel in place. Remove these screws and set them aside. On some models like the DLE5977W, there's a trim ring that snaps off first before you can access the screws. Use your flathead screwdriver to gently pry it loose if needed.
Step 2: Separate the Door Panels
With the screws removed, carefully lift the inner panel away from the outer door frame. The two halves will separate, revealing the latch assembly mounted on the door's edge. You'll see the spring-loaded catch mechanism and the mounting bracket — that's your target. Be careful not to drop any small springs or clips that might pop loose during separation.
Step 3: Remove the Failed Latch Assembly
The 4027EL1001A latch assembly is held by two screws on the door's edge. Remove these screws and pull the old latch straight out. You might need to compress the spring-loaded mechanism slightly to clear it from the door frame. Check the mounting area for any broken plastic pieces — a common failure mode is the plastic catch breaking off completely, which is why your door won't secure.
Step 4: Install the New Latch Assembly
Position the new 4027EL1001A latch into the mounting slot on the door's edge. Make sure the spring-loaded catch faces toward the dryer opening — it should align with the striker plate on the dryer frame. Secure it with the two mounting screws. Test the spring action by pressing the catch in and releasing it a few times. It should snap back firmly each time.
Step 5: Reassemble the Door Panels
Align the inner door panel back onto the outer frame, making sure the edges sit flush all the way around. Replace all the Phillips screws you removed in step one, working in a cross pattern to ensure even pressure. If your model has that snap-on trim ring, press it back into place until you hear it click. Close the door and test the latch — you should feel a solid click and the door should hold firmly shut.
Testing After Installation
Plug your dryer back in. Close the door and listen for that satisfying click of the latch engaging. Start a cycle — the dryer should recognize the closed door immediately and begin running. Open the door mid-cycle to verify the safety switch works (the dryer should stop instantly). If the dryer still won't start even with the door closed, check that the striker plate on the dryer frame isn't bent or misaligned.
Frequently Asked Questions
Will this latch work on both LG and Kenmore dryers?
Yes, the 4027EL1001A is the correct replacement for LG-manufactured dryers sold under both LG and Kenmore branding. This includes Kenmore Elite models in the 796 series like the 79680442900 and 79680443900. If your Kenmore model starts with 796, it's LG-built and this latch will fit.
My door closes but the dryer still won't start — is it the latch?
Possibly, but not always. The latch has a mechanical catch and often a separate door switch that signals the control board. If the plastic catch is broken, the door won't physically latch. If the switch contacts inside the latch are worn, the door will latch but the dryer won't start. Test by manually pressing the striker while the door is open — if the dryer starts, your latch assembly needs replacement.
Can I use this part on a front-load washer with the same model number format?
No. Despite having similar model numbering (DLE vs WM), this latch is specifically designed for LG dryers. Washers use a completely different door latch mechanism because they need to handle water pressure and locking during spin cycles. Always verify the part number matches your appliance type.
Test the spring action on the new latch before reassembling the door — it should snap back firmly with no sticking
Need the part for this repair?
4027EL1001A · In Stock · Ships next business day