How to Replace 134937300 Washer Door Strike Assembly on Electrolux Front-Load Washer — Step-by-Step

Your Electrolux washer door won't latch anymore. You push it closed, hear a weak click, but the machine refuses to start. The door strike — that metal catch on the washer's frame that holds the door latch in place — has either loosened, cracked, or worn down from thousands of cycles. On models like the EIFLS60JIW1 and EIFLS55IMB0, this part takes constant pressure every time you close that door, and eventually the metal fatigues or the mounting holes elongate.

What You Need Before Starting

• Phillips screwdriver
• Flathead screwdriver (for prying trim panel)
• Work gloves (metal edges can be sharp)
• Flashlight or work light

Estimated Time: 15-25 minutes

Difficulty: Easy — No disassembly of the washer cabinet required, just accessing the door frame area.

Safety First

Unplug your washer completely before starting. Even though you're working on the door frame and not internal electronics, you'll have your hands near the door lock mechanism, and you don't want any accidental cycle starts. Turn off the water supply too — if you bump the door open while there's water in the tub, you'll have a mess.

Step 1: Access the Door Strike Area

Open the washer door fully. The door strike assembly is mounted on the right side of the door opening, where the door latch catches when you close it. On most Electrolux front-loaders like the EIFLS60LSS0, there's a plastic trim piece around the door opening. Use your flathead screwdriver to carefully pry this trim away — it's held by clips. Start at the bottom corner and work your way around. Don't force it; these clips break easily.

Step 2: Remove the Old Strike Assembly

You'll see two Phillips screws holding the strike assembly to the metal frame. Remove both screws — they're usually Torx or Phillips head, about 1.5 inches long. The strike might be stuck from detergent residue buildup. Wiggle it gently while pulling forward. Check the mounting holes in the frame — if they're elongated or damaged, you'll need to shift the new strike slightly to catch fresh metal.

Step 3: Clean the Mounting Surface

Wipe down the area where the strike was mounted. Use a damp cloth to remove any detergent buildup, rust, or debris. This ensures the new strike sits flush against the frame. If there's rust in the screw holes, use a wire brush or small file to clean it out — you want those screws to bite into solid metal.

Step 4: Install the New 134937300 Strike Assembly

Position the new strike assembly in the mounting holes. Before you tighten anything, close the washer door and check alignment — the door latch should engage the strike catch smoothly without forcing. Adjust the position if needed. Once aligned, tighten both mounting screws firmly but don't overtighten — you're screwing into sheet metal, and you can strip the holes.

Step 5: Reinstall the Trim and Test

Snap the door trim piece back into place, working from top to bottom. Press firmly on each clip location until you hear it seat. Close the door and listen for a solid, confident click. Start a rinse cycle to verify the door lock engages properly and the washer starts normally. Open and close the door five or six times to make sure the strike holds under repeated use.

Testing After Installation

Run a quick rinse-and-spin cycle with no clothes. Listen for the door lock solenoid to engage — it should make a distinct clicking sound about 3 seconds after you start the cycle. If the machine starts but then stops with a door error code, the strike might need slight repositioning. Loosen the screws, adjust forward or backward slightly, and retest.

Frequently Asked Questions

Will this strike assembly fit both Electrolux and Frigidaire front-load washers?

Yes. Part 134937300 replaces AP4365553, 7134937300, 1483065, and PS2345126. It's used across Electrolux models like the EIFLS55IIW0 and EIFLS60JIW1, and Frigidaire models that share the same door frame design. Always verify your model number against the compatibility list.

How do I know if the door strike or the door latch is the problem?

Close the door and watch what happens. If the latch extends but doesn't catch anything, the strike is damaged or misaligned. If the latch doesn't extend at all and you get a door error code, the latch assembly itself (part 131763202) is likely the culprit. The strike is just a metal catch — it doesn't have electronics.

Can I use the washer if the door strike is cracked but still latching?

Not safely. A cracked strike can fail mid-cycle, which means the door could pop open during spin. High-speed spin cycles generate serious force. A failed strike during spin can throw the door open violently and potentially cause injury or flood damage. Replace it as soon as you notice damage.