Troubleshooting

Whirlpool Washer Won't Start or Lid Won't Lock — 5 Causes & Fixes

6 min read
May 24, 2026
Multiple root causes covered
Most common cause
Cracked or broken lid strike from repeated impact stress
Avg repair cost
$19–$300
DIY difficulty
Easy for strike replacement, moderate for actuator, advanced for board
Symptom checklist
Lid closes but cycle won't start
Washer won't fill with water or begin agitation when lid is closed and start is pressed
Lid lock error code displayed
Control panel shows F5E2, LF, or specific lid error message preventing operation
Visible crack in white plastic lid strike
Hairline fracture or complete break visible on lid strike tab underneath lid
Clicking sound with no engagement
Audible click when closing lid but lock mechanism doesn't secure properly
Lid feels loose when closed
No firm click or secure feeling when lid closes, can lift slightly when locked
Root cause analysis
W10837741 W10837741 Washer Lid Strike Compatible with Whirlpool Maytag Kenmore Amana Crosley, Replaces W10714899 AP5988753 PS11726338 4338531

You load the laundry, close the lid, press start... and nothing. Your Whirlpool washer sits there silently, refusing to fill or spin. The control panel might show lights, but the cycle won't begin. In most top-load Whirlpool, Maytag, and Kenmore washers built after 2011, this is almost always the lid strike — a small white plastic tab on the underside of the lid that's either cracked, misaligned, or completely snapped off.

The lid strike (part W10837741) engages with the lid lock mechanism mounted inside the washer cabinet. When it fails, the washer's control board thinks the lid is open and prevents the cycle from starting. This is a built-in safety feature, but it's frustrating when the part itself breaks.

Quick Symptom Check

Your washer likely has a failed lid strike if you're experiencing:

  • Lid closes but cycle won't start — no water fills, drum doesn't spin
  • Lid lock error code — display shows F5E2, LF, or lid error message
  • Clicking sound when you close the lid — but no engagement
  • Visible crack or missing piece — white plastic tab on lid underside is broken
  • Lid feels loose or doesn't click — no firm engagement when closing

Cause #1: Cracked or Broken Lid Strike (70% of Cases)

Why it happens: The W10837741 lid strike is injection-molded plastic that takes repeated impact every time you close the lid. After hundreds of cycles, stress fractures develop around the mounting holes. Eventually, the strike cracks clean through or the mounting tabs break off.

How to diagnose: Open the washer lid and look at the underside — you'll see a white plastic piece about 3 inches long mounted near the center hinge. If you see hairline cracks, a missing chunk, or the piece moves when you touch it, that's your problem. On models WTW5000DW1, WTW4955HW0, and MVWC565FW1, this part typically fails between years 3-5 of ownership.

The fix: Replace the strike. Remove two screws holding the old strike, snap the new W10837741 into position, and secure with screws. Total repair time: 10 minutes. Cost: $18.99 for the OEM replacement.

Cause #2: Misaligned Lid Strike (15% of Cases)

Why it happens: Someone slammed the lid hard, or the mounting screws loosened over time. The strike shifts a quarter-inch forward or backward, so it no longer aligns with the lid lock actuator inside the cabinet.

How to diagnose: Close the lid slowly and watch whether the strike centers over the opening in the top panel. If it's off to one side, you'll hear it scrape or miss the lock mechanism entirely. Check if the mounting screws are loose — on Whirlpool models WTW4816FW2 and 7MWTW1700EM0, the plastic can deform slightly, allowing movement.

The fix: Loosen the screws, reposition the strike so it's centered, then retighten firmly. If screw holes are stripped, you'll need to replace the strike anyway since the plastic threads won't hold.

Cause #3: Failed Lid Lock Actuator (10% of Cases)

Why it happens: The actuator inside the washer cabinet contains a small motor and latch that grabs the lid strike. If this motor burns out or the latch jams, the strike can't engage even when it's perfectly intact.

How to diagnose: Your strike looks fine — no cracks, properly aligned. But when you close the lid and press start, you don't hear the characteristic click or mechanical whir of the lock engaging. You might hear a buzzing sound instead, indicating the actuator is trying but failing.

The fix: This requires accessing the actuator inside the cabinet, which means unplugging the washer and removing the top panel. If you're not comfortable with that level of disassembly, call a tech. Parts run $60-90 for the actuator assembly.

Cause #4: Worn Strike Surface (3% of Cases)

Why it happens: Years of friction wear down the engagement surface of the strike. It's not visibly cracked, but the plastic has been ground smooth where the lock mechanism grabs it, so there's not enough grip to trigger the sensor.

How to diagnose: Run your finger across the strike's engagement area — it should feel slightly textured. If it's completely smooth and shiny, especially on high-use washers (families running 2+ loads daily), wear is your issue.

The fix: Replace the strike. You can't repair worn plastic effectively.

Cause #5: Control Board Fault (2% of Cases)

Why it happens: The main control board has a stuck relay or software glitch that prevents it from recognizing lid closure, even when both the strike and actuator are working perfectly.

How to diagnose: Everything looks and sounds normal mechanically, but the washer still won't start. You've already replaced the strike with no improvement. Try a hard reset: unplug the washer for 5 minutes, then plug back in. If it works temporarily but the problem returns, it's likely a board issue.

The fix: Board replacement is $150-300 in parts plus labor. Get a technician to verify the diagnosis first — boards are expensive to guess on.

When to Call a Pro

If you've replaced the lid strike and confirmed it's aligned, but your Whirlpool washer still won't start, you're past DIY territory. The issue is either the lid lock actuator (requires cabinet disassembly) or the control board (requires diagnostic testing). A service call runs $100-150 for diagnosis, and most techs will credit that toward the repair if you proceed.

For models WTW4810EW2, MVWC465HW0, and related Kenmore series, Whirlpool released a technical service bulletin about intermittent lid lock failures — if your washer is still under extended warranty, this might be covered.

Frequently Asked Questions

Can I bypass the lid lock to use my washer temporarily?

Technically yes, but don't. The lid lock prevents the washer from spinning at 1200 RPM with the lid open — that's a serious safety hazard. If you bypass it and someone (like a kid) opens the lid during spin, the results could be catastrophic. Replace the $18.99 strike instead of risking injury.

Will any white plastic piece work as a replacement?

No. The W10837741 strike has specific dimensions and positioning that trigger the magnetic or mechanical sensor in the lock actuator. Generic plastic won't work. You need the OEM part or an exact aftermarket equivalent that replaces AP5988753, W10714899, PS11726338, or 4338531.

How long does the lid strike typically last?

Depends on usage. Light use (3-4 loads per week): 5-7 years. Heavy use (10+ loads per week): 3-4 years. If you habitually slam the lid shut, that cuts lifespan significantly. Close it gently and the replacement strike should last another 5+ years on models like WTW4850HW0 and MVWC555DW1.

Diagnosed the problem?

W10837741 · In Stock · Fast shipping

Shop W10837741 →
Likely parts needed
W10837741
W10837741 Washer Lid Strike Compatible with Whirlpool Maytag Kenmore Amana Crosley, Replaces W10714899 AP5988753 PS11726338 4338531
$13.99
Add to Cart