Whirlpool Washer Lid Lock Strike Parts — Models & Compatibility

Your Whirlpool washer won't start, and you've already pressed the button three times. The lid's closed, but the machine acts like it isn't. This is the exact failure pattern for the lid lock strike — a small plastic piece under the lid that tells the washer it's safe to run. When this $15 part fails, your entire machine shuts down. This hub covers the W10240513 lid lock strike that fits over 500 Whirlpool, Maytag, Amana, and Kenmore top-load washers from the late 2000s through current models.

Is This the Right Part for Your Model?

Check your model number on the sticker inside the washer lid or along the top rim of the tub. If you've got a WTW or MVW series machine, this is likely your part. The strike works with direct-drive top-loaders that have electronic lid locks — if you hear a clicking sound when you close the lid (or used to), you're in the right place. Cross-reference your full model number with our compatibility list below before ordering.

About This Replacement Part

The lid lock strike is the receiving piece that the lid latch mechanism grabs when you close the washer lid. It's a simple plastic component screwed into the underside of the lid, but it takes the full force of every lid closure — thousands of cycles over the washer's life. When it cracks or warps, the latch can't engage properly, and the washer's control board won't allow the cycle to start. You'll see symptoms like the washer refusing to start, the lid appearing closed but not locking, or error codes related to lid detection.

This part typically fails after 5-8 years of regular use, especially if the lid's been slammed shut repeatedly. One Maytag owner reported: "My washer was not agitating properly and was not spinning at all... I ordered a Lid Latch Assembly and a Lid Switch Strike... My washer now runs just like it did when it was brand new!" Another customer saved $600 in repair costs by replacing this part themselves: "OK this is one of those stories that can't help but encourage those of us who have absolutely no idea how appliances work and yet by simply refusing to pay such ridiculous repair prices can honestly get it done with a 'FRACTION' of the cost."

Installation Overview

This is one of the easiest washer repairs you'll do. The strike is located under the lid and held in place by two Phillips-head screws. Open the lid fully, support it so it doesn't fall back, and you'll see the strike mounted to the underside. Remove the two screws, pull out the old strike, drop in the new one, and reinstall the screws. Total time: 15-30 minutes. You don't need to unplug the washer or move it away from the wall. As one parent put it: "Following the clear video instructions for each part, my handy teenage son was able to remove the lid latch assembly and replace it with the new part as well as the lid switch strike. The washer is back to working perfectly for under $100."

Tools You'll Need

• Phillips-head screwdriver
• Adjustable wrench (if removing lid for easier access)
• Towel or cloth to protect lid finish

Compatible Whirlpool Washer Models

This W10240513 lid lock strike fits Whirlpool, Maytag, Amana, Kenmore, and Roper top-load washers. Check your model number against this list:

When to Replace This Part

You need a new lid lock strike if your washer shows these symptoms: won't start even with lid closed, lid won't lock when you press start, clicking sound but no lock engagement, or F5E2 error code (lid not locking). Sometimes you'll see physical damage — cracks in the plastic strike or worn mounting holes. If your washer stopped mid-cycle and now refuses to restart, check this part first before calling a tech.

Part Numbers & Cross-References

This part replaces several older Whirlpool part numbers: WPW10240513, AP6017583, PS11750882, 1873013, AP4514459, and PS2579805. If you're searching by any of these numbers, you're looking at the same current part. Whirlpool consolidated these under W10240513, but the design hasn't changed.