Maytag Washer Pump & Drive Belt Kit Parts — Models & Compatibility

If your Maytag washer won't drain, leaves clothes soapy and wet, or makes grinding noises during the spin cycle, you're likely dealing with a worn pump or drive belt. This 12112425 kit includes both the pump belt and drive belt — the two most common failure points in Maytag's classic top-load washer lineup. It fits over 100 models across the LAT, LA, and A-series washers.

Is This the Right Part for Your Model?

This kit works with Maytag top-load washers manufactured between the late 1990s and early 2010s. Check your model number — it's usually on a metal plate inside the washer lid or on the back panel. If you've got an LA806, LAT2500, LAT5910, or any model starting with "LA" or "LAT," you're in the right place. The part replaces AP4011179, 211124, 211125, W10175481, and PS2005284.

About This Replacement Kit

Maytag's belt-driven washers use two separate belts: one connects the motor to the pump (handles draining), and the other drives the transmission (handles agitation and spinning). When either belt stretches, cracks, or snaps, you'll see symptoms fast. Common signs include water that won't drain, a washer that won't agitate, slow or weak spinning, burning rubber smells, or excessive noise during cycles. One customer reported their "washer would not drain water and left clothes soapy and wet" — a textbook pump belt failure. Another mentioned they were doing "easy preventive maintenance" by replacing both belts before total failure. Smart move, since this is a 30-60 minute repair with basic tools.

Why Both Belts Fail Together

Here's the thing about washer belts: they age at roughly the same rate. If one's worn enough to fail, the other isn't far behind. That's why this kit includes both. You'll need a nutdriver, screwdrivers, and a socket set to access the belts — they're located under the washer cabinet. The repair difficulty is rated moderate because you'll need to tip the washer and work in a tight space, but the actual belt replacement is straightforward once you're in there.

Compatible Maytag Washer Models

This kit fits LAT-series (Maytag's workhorse residential line), LA-series (commercial-grade models), and A-series washers. Below are confirmed compatible models — if yours isn't listed but starts with these prefixes and was made before 2012, it likely fits.

• LA Series: LA806, LA882, LA8820, LA9400
• LAT1000-2000 Series: LAT1910, LAT1916, LAT2200, LAT2300, LAT2500, LAT2600, LAT2910
• LAT3000-4000 Series: LAT3500, LAT3910, LAT4000, LAT4910
• LAT5000+ Series: LAT5000, LAT5804, LAT5910, LAT7300
• A Series: A8820, A7800

Installation Tips from Real Repairs

Unplug the washer before you start — obvious but critical. You'll need to remove the front panel (usually four screws) and tip the washer back against a wall to access the bottom. The pump belt is smaller and wraps around the pump pulley. The drive belt is longer and loops around the motor and transmission pulleys. Take a photo of the belt routing before removal — it'll save you frustration during reassembly. Check both pulleys for wear while you're in there. If they're grooved or damaged, the new belts won't last.

What Causes These Belts to Fail

Overloading is enemy number one. When you cram too many heavy towels into the drum, the motor strains, the belts heat up, and they deteriorate faster. Regular use also just wears them down — rubber degrades over time, especially in humid laundry rooms. You'll know failure is imminent when you hear squealing during agitation or notice the drum spinning slower than usual. Don't ignore a burning smell either — that's belt material overheating from slippage.

Preventing Future Belt Failures

Balance your loads. Seriously, that's 80% of the battle. An unbalanced load forces the transmission to work harder, which stresses the drive belt. Also, don't let wet clothes sit in the drum for hours after a cycle — the extra weight puts tension on the belt system. If you hear any squeaking or notice performance issues, investigate immediately. Catching a worn belt before it snaps prevents water damage from failed drain cycles.