Whirlpool, Maytag & Amana Dryer High Limit Thermal Fuse Parts — Models & Compatibility

Your Maytag dryer suddenly won't heat, or maybe it won't start at all. You've checked the breaker, cleaned the vent, but nothing's changed. There's a good chance the high limit thermal fuse has blown — a one-time-use safety device that trips when your dryer overheats. This hub covers the 40113801 thermal fuse that fits over 200 Whirlpool, Maytag, Amana, and Admiral dryer models.

Is This the Right Part for Your Model?

Check your dryer's model number — it's usually on a metal tag inside the door opening or on the back panel. Models like the MEDC400VW0, MDE208DAYW, MDG308DAWW, and PDET910AYW all use this exact thermal fuse. Cross-reference your full model number with the compatibility list below to confirm fitment before ordering.

About This Replacement Part

The 40113801 high limit thermal fuse is a critical safety component that monitors your dryer's temperature. When airflow gets restricted — usually from a clogged vent or blocked lint screen — the dryer overheats and this fuse blows to prevent a fire. Once it trips, it's done. You can't reset it. Common symptoms include a dryer that won't heat, won't start, or runs but gets dangerously hot. This fuse replaces Whirlpool part numbers WP40113801, AP6009129, 14218937, 62600, and 915698. It's typically mounted on the blower housing or exhaust duct, and you'll need to address whatever caused the overheat before installing the new fuse — otherwise, it'll just blow again.

Compatible Models

This thermal fuse fits these Whirlpool-family dryer models:

• MDE208DAYW — Maytag
• MDE2706AYW — Maytag
• MDG2706AWW — Maytag
• MDG308DAWW — Maytag
• MDG3706AWW — Maytag
• MDGT336AWW — Maytag
• MDGT446AWW — Maytag
• SDE3606AYW — Maytag
• SDE305DAYW — Maytag
• SDG3606AWW — Maytag
• PDET910AYW — Maytag
• PDET920AYW — Maytag
• MEDC400VW0 — Maytag
• MEDC215EW1 — Maytag
• ADE7005AKW — Admiral
• ADE7005AYW — Admiral
• ADE9005AGW — Admiral

Plus over 180 additional Whirlpool, Maytag, Amana, and Admiral models. Verify your exact model number before ordering.

Why This Fuse Blows

Understanding why the thermal fuse tripped is just as important as replacing it. The most common causes: a severely clogged dryer vent restricting airflow, a blocked lint filter, or a failed heating element cycling too hot. Some techs see this part fail when homeowners use long, flexible vinyl vents that trap lint. Before you install the new fuse, pull your dryer out and disconnect the vent. Check for blockages. Run your hand through the duct. If you feel significant lint buildup, clean it thoroughly — or you'll be replacing this fuse again in a month.

Installation Tips

You'll need a screwdriver and possibly a nut driver to access the fuse. Most Maytag dryers require removing the front panel or top to reach the blower housing where this fuse mounts. The fuse itself is held by two wires — pull them off with needle-nose pliers, remove the mounting screw, and reverse the process with your new part. Test continuity on the old fuse with a multimeter if you want confirmation it's blown (you should read infinite resistance). Don't skip the vent inspection. Seriously. That's what caused this failure in the first place.

Order Your Replacement

The 40113801 thermal fuse is in stock at $10.99. It ships same-day if ordered before 3 PM EST. You're getting an exact-fit replacement that meets OEM specifications for Whirlpool, Maytag, and Amana dryers.