Samsung Washer Drain Clutch Motor Parts — Models & Compatibility

Your Samsung top-load washer won't drain, or it's making grinding noises during the spin cycle. That's usually the drain clutch motor—the component that controls water drainage and spin speed transitions. This hub covers DC31-20014C replacement parts for Samsung washer models, including the WA50R and WA54R series.

Is This the Right Part for Your Model?

The drain clutch motor fits specific Samsung top-load washers, primarily 2019-2023 models with activewash technology. Check your model number on the label inside the washer lid or on the back panel. It'll start with "WA" followed by capacity numbers (45, 50, or 54). Match it against the compatible models list below to confirm fitment.

About This Replacement Part

The DC31-20014C drain clutch motor (replaces AP4211210, PS4204941, 2068406, SWD-118) manages the mechanical drain pump clutch mechanism in Samsung's newer top-load washers. Unlike older belt-driven systems, this motor electronically engages the drain pump and controls spin transitions. When it fails, you'll notice water sitting in the tub after cycles, clothes coming out soaking wet, or error codes like DC or dC on the display. The motor assembly includes the clutch actuator and mounting bracket—you're replacing the entire unit, not just rebuilding it.

Compatible Samsung Washer Models

This drain clutch motor fits the following Samsung washer models. If your exact model isn't listed but shares the same series prefix, it likely uses this part:

WA54R Series (5.4 cu. ft. capacity)

• WA54R7600AV/US-00
• WA54R7600AW/US
• WA54R7200AW/US-02
• WA54R7200AV/US

WA50R Series (5.0 cu. ft. capacity)

• WA50R5400AV/US
• WA50R5400AW/US-02
• WA50R5200AW/US-02
• WA50R5200AV/A4

WA45T Series (4.5 cu. ft. capacity)

• WA45T3400AW/A4-00
• WA45T3400AP/A4-00
• WA45T3400AV/A4
• WA45T3200AW/A4

Common Drain Clutch Motor Failure Signs

Before ordering, verify the drain clutch motor is actually your problem. Here's what typically happens when this part fails:

• Water Won't Drain: Tub fills but stays full after wash cycle completes
• Grinding or Clicking: Loud mechanical noises during drain attempts
• Intermittent Drainage: Sometimes drains completely, other times leaves standing water
• Error Codes: DC, dC, or 5C codes indicating drainage problems
• Won't Spin: Washer agitates but won't transition to high-speed spin

What's Included

The DC31-20014C comes as a complete motor assembly. You get the drain clutch motor, mounting bracket, and electrical connector. You'll reuse your existing wiring harness—just unplug the old motor and plug in the new one. Samsung designed this as a direct replacement unit to simplify repairs.

Installation Overview

Replacing the drain clutch motor requires accessing the bottom of the washer. You'll need to tip the machine back or lay it on its side to reach the underside panel. The motor mounts with three bolts and has a single electrical connector. Most DIYers complete this repair in 30-45 minutes once they have the washer positioned correctly.

Verify Your Part Number

Samsung stamps the part number directly on the motor housing. If you can access your current motor, check for DC31-20014C, or the older superseded numbers: AP4211210, PS4204941, 2068406, or SWD-118. They all refer to the same updated motor assembly. If those numbers match, you've confirmed the right part.

Order Your Replacement Part

Need this drain clutch motor for your Samsung washer? We stock the DC31-20014C at $148.99 with fast shipping. It's a genuine Samsung replacement part with the updated design that addresses earlier motor failures. Order today and get your washer draining properly again by this weekend.