GE Washer Water Inlet Valve Parts — Models & Compatibility

Your GE washer's water inlet valve controls how water flows into the tub during fill cycles. When this valve fails, you'll see symptoms like no hot or cold water entering the drum, slow fill times, or water leaking from the back of the machine where the hoses connect. The WH13X24386 valve assembly is the OEM replacement that fits most GE and Hotpoint top-load washers in the GTW series manufactured between 2015-2020.

Is This the Right Part for Your Model?

Check your washer's model number — it's typically located inside the door opening on the top edge of the tub, or behind the control panel. If your model number starts with GTW460, GTW465, GTW485, GTW490, GTW500, GTW600, or GTW700, this valve likely fits. Cross-reference your exact model number against the compatibility list below to confirm.

About This Replacement Part

The WH13X24386 is a dual-inlet valve assembly that manages both hot and cold water supply lines. It replaces previous part numbers WH13X26535, WH13X24392, AP6892695, and 4931303. Common failure modes include internal solenoid burnout (washer won't fill at all), diaphragm deterioration (causes continuous slow leaking even when machine is off), and mineral buildup in hard water areas that restricts flow. If your washer is stuck on the fill cycle or you hear the valve humming but no water enters, the solenoid coils have likely failed. Water pooling behind the washer after cycles indicates the valve isn't sealing properly and needs replacement.

Compatible GE & Hotpoint Washer Models

This water inlet valve fits the following GE and Hotpoint top-load washer models:

• GTW460 Series: GTW460ASJAWW, GTW460ASJ0WW, GTW460AMJ0WW, GTW460AMJ1WW
• GTW465 Series: GTW465ASN1WW, GTW465ASN2WW, GTW465ASN3WW, GTW465ASN8WW, GTW465ASN9WW
• GTW485 Series: GTW485ASJ0WS, GTW485ASJ1WS, GTW485ASJ2WS, GTW485ASW0WB
• GTW490 Series: GTW490ACJ0WW, GTW490ACJ1WS, GTW490ACJ1WW, GTW490ACJ2WS, GTW490ACJ4WS, GTW490ACJ5WS
• GTW500 Series: GTW500ASN0WW, GTW500ASN1WW, GTW500ASN2WW
• GTW600 Series: GTW600ASN0WW, GTW600ASN1WW
• GTW700 Series: GTW700ASN0WW, GTW700ASN1WW

And many more GE top-load models. Verify your specific model number before ordering.

Symptoms This Part Fixes

• Leaking: Water drips or pools behind the washer when machine is idle
• Water Filling Issues: Washer takes forever to fill, or fills extremely slowly on one or both temperatures
• No hot or cold water: Washer won't fill at all, or only fills with one temperature regardless of cycle selection

Installation Overview

Replacing the water inlet valve requires accessing the back panel of your washer. You'll need to shut off both hot and cold water supply valves, disconnect the fill hoses, remove the back access panel, disconnect the wire harness from the old valve, unbolt the valve bracket, and reverse the process with the new valve. Make sure to inspect the inlet screens inside the valve ports — if they're clogged with sediment, clean them before installation to prevent future flow restrictions.

Part Specifications

• Part Number: WH13X24386
• Replaces: WH13X26535, AP6892695, WH13X24392, 4931303
• Price: $28.99
• Valve Type: Dual inlet (hot and cold)
• Connection: Standard 3/4" threaded hose fittings

Why This Valve Fails

Water inlet valves fail because the internal solenoid coils wear out after thousands of open/close cycles — typically after 5-8 years of regular use. Hard water accelerates failure by depositing calcium on the rubber diaphragm, preventing it from sealing completely. If you've got well water or live in an area with mineral-heavy supply, expect shorter valve lifespan. Power surges can also burn out the solenoid coils instantly, which is why you'll sometimes see sudden failure with no warning signs.