GE Range Double Burner Assembly Parts — Models & Compatibility

Your GE range's double burner assembly is the workhorse of your cooktop — it's what delivers consistent heat for everything from simmering sauces to boiling pasta water. When it fails, you'll know immediately: uneven heating, one side working while the other stays cold, or no heat at all despite clicking and gas flow. This replacement part (WB16K10026) fits over 100 GE, Hotpoint, and Kenmore gas range models and restores your burner to factory performance.

Is This the Right Part for Your Model?

Check your range's model number before ordering. You'll find it on a metal tag inside the oven door frame, on the control panel behind the storage drawer, or along the front frame when you open the oven door. This double burner assembly is a direct replacement for AP2633210, WB29K17, 868697, and WB16K10003, and works across multiple GE series including AGBS, JGBS, and RGB models from the late 1990s through mid-2000s.

About This Replacement Part

The WB16K10026 is a complete double burner assembly that includes both the inner and outer burner rings in one unit. This part typically fails after years of use when the gas ports become clogged beyond cleaning, when the burner head warps from repeated thermal cycling, or when the metal develops cracks that prevent proper gas distribution. Unlike single burner heads that you can sometimes clean and restore, a warped or cracked double burner assembly needs full replacement — there's no repair option that's worth the hassle. The good news? This is a straightforward swap that takes about 15 minutes with basic tools.

Compatible GE Range Models

This burner assembly works with the following models. If your model number isn't listed but starts with similar letters and numbers, check the original part number on your existing burner assembly:

• AGBS300 Series: AGBS300EP1BB, AGBS300EP1WW, AGBS300EP2BB, AGBS300EP2WW, AGBS300EP3BB, AGBS300EP3WW, AGBS300EP4BB, AGBS300EP4WW, AGBS300PJ1WW, AGBS300PJ3WW, AGBS300PJ4WW, AGBS300PJ5WW, AGBS300PK1BB, AGBS300PK5BB
• JGBS20 Series: JGBS20WEA1WW, JGBS20WEA3WW, JGBS20WEA4WW, JGBS20WEA5WW, JGBS20WEH1WW

This part also fits select Hotpoint and Kenmore gas ranges that used GE components during this production period. Cross-reference your existing part number to confirm compatibility.

What You're Getting

The complete double burner assembly includes both burner rings pre-assembled and ready to install. You're not buying separate components that need alignment or adjustment — it's one piece that drops right onto the burner base. The brass ports are already drilled to GE's specifications for proper gas flow and flame pattern. Just remove your old assembly (lift it straight up), clean the burner base if needed, and set the new one in place.

Why This Part Fails

Double burner assemblies fail for three main reasons. First, repeated heating and cooling cycles eventually warp the metal, which throws off the flame pattern and creates hot spots. Second, food spills and boil-overs corrode the burner ports over time — even if you clean regularly, acidic spills eat away at the brass fittings. Third, the outer ring often cracks near the mounting points after years of expansion and contraction. Once any of these happen, you can't clean or adjust your way back to proper performance. The burner assembly is done, and replacement is the only fix that works.

Installation Overview

Turn off the gas supply at the wall valve or main line. Remove the burner grate and lift cap. The double burner assembly sits on the cooktop base with no screws — just lift it straight up to remove. Clean any debris from the base where the new burner will sit, then position the new assembly so the gas inlet tube aligns with the feed pipe. Press down gently to seat it fully. Turn the gas back on, test for leaks with soapy water around connections, then fire up each ring to verify proper flame pattern. You should see blue flames across both rings with no yellow tips or gaps.