Whirlpool Top Load Washer Lid Lock Assembly Parts — Models & Compatibility

Your Whirlpool top-loader won't start, and you hear clicking from the lid area. That's the lid lock assembly failing to engage — one of the most common failure points in WTW series washers. This hub covers the W11394572 lid lock assembly that fits Whirlpool, Maytag, and Kenmore top load washers manufactured from 2017 onward.

Is This the Right Part for Your Model?

Check your washer's model number on the sticker inside the washer lid opening or along the top edge of the tub. This lid lock assembly works with WTW5100, WTW5105, WTW6120, WTW7120, and WTW8120 series washers. The part number W11394572 replaces older versions W11032875, W11543566, AP6973174, and PS12731130 — so if you've found any of those numbers in your research, this is the updated replacement.

About This Replacement Part

The lid lock assembly is the mechanism that secures your washer lid during the spin cycle. When it fails, you'll typically see three symptoms: the washer won't start at all, the lid won't close properly, or you'll hear repeated clicking as the lock tries to engage but can't. The W11394572 is a complete assembly that includes the latch mechanism, strike, and wiring harness. Whirlpool redesigned this part to address durability issues with earlier versions — the locking pawl now uses reinforced plastic that holds up better to the constant engage-disengage cycles during normal use.

Compatible Whirlpool Washer Models

This lid lock fits the following Whirlpool top load washer models. If your model isn't listed but starts with WTW5100, WTW5105, WTW6120, WTW7120, or WTW8120, it's likely compatible — verify by comparing your current part number:

• WTW5100HC0 — Whirlpool 4.3 cu ft top load washer
• WTW5100HW0 — Whirlpool top load washer, white
• WTW5105HC0 — Whirlpool 4.3 cu ft washer with deep fill option
• WTW5105HW0 — Whirlpool top load washer
• WTW5105HW1 — Whirlpool top load washer, revision 1
• WTW5105HW2 — Whirlpool top load washer, revision 2
• WTW6120HC0 — Whirlpool 4.8 cu ft top load washer
• WTW6120HC1 — Whirlpool 4.8 cu ft washer, revision 1
• WTW6120HW0 — Whirlpool top load washer, white
• WTW6120HW1 — Whirlpool top load washer, white revision 1
• WTW7120HC0 — Whirlpool 5.3 cu ft top load washer
• WTW7120HW0 — Whirlpool 5.3 cu ft washer, white
• WTW8120HC0 — Whirlpool smart top load washer
• WTW8120HW0 — Whirlpool smart washer, white

Why This Part Fails

Lid locks fail for two main reasons. First, the plastic striker that the lock grabs wears down over time — especially if you tend to close the lid firmly. Second, the internal solenoid that controls the locking mechanism can burn out, usually after 5-7 years of regular use. You'll know it's the solenoid if you hear clicking but the lock never fully engages. The good news is this assembly includes both components, so one replacement fixes both potential failure points.

What's Included

The W11394572 kit includes the complete lid lock assembly with integrated wiring harness and mounting hardware. You're getting the lock mechanism, the striker plate, and the connector that plugs into your washer's main control board. No additional brackets or screws needed — everything's in the box.

Cross-Reference Part Numbers

This part supersedes and replaces: W11032875, W11543566, AP6973174, PS12731130. If you're looking up your washer's parts diagram and see any of those numbers listed, the W11394572 is the current replacement Whirlpool supplies.