Whirlpool Washer Suspension Rod Kit Parts — Models & Compatibility

If your Whirlpool top-load washer sounds like it's launching into orbit during the spin cycle, or if the drum is banging against the cabinet, you're probably looking at worn suspension rods. This W10247710 suspension rod kit is designed specifically for Whirlpool, Maytag, and Kenmore Cabrio-style washers—the same machines that revolutionized laundry with their impeller wash systems but introduced a new weak point in the suspension design.

Is This the Right Part for Your Model?

This suspension rod kit fits the WTW7000, WTW7600, WTW7800, WTW8000, and WTW8500 series washers. You'll find your model number on a sticker inside the washer lid or on the back panel near the top. Look for model numbers starting with WTW followed by four digits—if you've got a WTW7800XW2 or WTW8500DC0, you're in the right place.

The kit replaces part numbers AP4411122, W10277357, W10237427, and PS2355518. If your repair paperwork or service manual lists any of those numbers, this W10247710 kit is what you need.

About This Replacement Part

Whirlpool's Cabrio and Bravos washers use four suspension rods to keep the wash basket stable during high-speed spins—up to 1,100 RPM in some models. These rods connect the outer tub to the washer cabinet frame, and they take a beating with every load. Over time, the rubber bushings inside the rods deteriorate, the metal fatigues, and suddenly your washer is walking across the laundry room floor or making sounds that concern the neighbors.

The W10247710 kit includes all four suspension rods you'll need for a complete repair. Whirlpool designed these as a matched set because uneven suspension causes the same problems as failed rods—excessive vibration, off-balance errors, and premature bearing wear. Most technicians won't replace just one rod for exactly that reason.

Compatible Models

This suspension rod kit works with over 20 Whirlpool washer models, including:

• WTW7800XW4, WTW7800XW3, WTW7800XW2, WTW7800XW1
• WTW7800XL4, WTW7800XL2, WTW7800XL1
• WTW7800XB4, WTW7800XB3, WTW7800XB2, WTW7800XB1
• WTW7600XW2, WTW7600XW1, WTW7600XW0
• WTW8500DC0, WTW8500DC1
• WTW8000DW0, WTW8000DW1
• WTW7000DW0, WTW7000DW1, WTW7000DW2

These models span Whirlpool's Cabrio and Bravos lines from approximately 2009 to 2016. The design remained consistent across this entire production run, which is why one suspension rod kit covers so many model variations.

When You Need This Part

You'll know it's time for new suspension rods when your washer starts exhibiting specific behaviors. The most obvious sign is excessive noise during the spin cycle—not just the normal hum, but banging, clunking, or rattling sounds that get worse as the drum speeds up. Some washers will also throw error codes related to load balance, stopping mid-cycle because the control board detects unsafe movement.

Another telltale sign is the washer walking across the floor. Even if you've got it on a perfectly level surface with the feet properly adjusted, failed suspension rods let the tub swing too far off-center during spin, and physics takes over. You'll come back to find your washer a foot away from where it started.

What's Included

The W10247710 kit contains:

• Four suspension rods (complete assemblies with bushings)
• Mounting hardware where applicable

You're getting OEM-equivalent parts designed to Whirlpool's original specifications. The rods are pre-assembled with the rubber bushings already installed, so there's no fiddly assembly work before you start the repair.

Installation Considerations

Replacing suspension rods isn't a five-minute job, but it's well within DIY territory if you're comfortable working with basic hand tools. You'll need to remove the washer cabinet, disconnect a few wire harnesses, and support the wash tub while you swap out the old rods for new ones. The entire repair typically takes 45 minutes to an hour for someone with moderate repair experience.

The most important tip: replace all four rods at once. I know it's tempting to just swap the obviously broken one, but mismatched suspension creates the same vibration issues you're trying to fix. Plus, if one rod has failed, the others aren't far behind—they've all experienced the same wear cycles and load stress.

Why Choose This Part

At $109.99, the W10247710 kit costs about what you'd pay for a single service call, and you're getting all four rods plus the satisfaction of fixing it yourself. Compare that to the $300-400 most repair services charge for this job, and the math makes sense pretty quickly.

This part ships directly to your door, usually within a few business days. No waiting weeks for the repair tech to fit you into their schedule, no taking time off work to be home for the service window. Order it, watch a couple installation videos while you wait for delivery, and you'll have your washer running smoothly again in under a week.