Samsung Dryer Lint Filter Assembly Parts — Models & Compatibility

If you own a Samsung DV-series dryer, the DC97-16013A lint filter assembly is your primary defense against lint buildup and restricted airflow. This hub covers compatibility across Samsung's most common dryer models from the DV210 through DV520 series, plus Kenmore models built by Samsung. Whether you're dealing with a cracked filter housing or a warped screen that no longer seats properly, this is the OEM-spec replacement that restores proper lint capture.

Is This the Right Part for Your Model?

Your model number is stamped on a label inside the dryer door opening — usually on the right side of the door frame. Samsung DV-series models follow a pattern like DV210AEW/XAA or DV330AGW/XAA. The DC97-16013A fits the entire lineup from 2008-2014 Samsung electric and gas dryers, including those sold under the Kenmore brand (typically Kenmore Elite 796-series). Cross-reference your exact model against the compatibility list below before ordering.

About This Replacement Part

The DC97-16013A is the complete lint filter assembly — it includes both the screen and the plastic housing that slides into your dryer's lint trap slot. Samsung engineered this as a single unit because the housing provides the seal that prevents lint from bypassing the screen and entering the blower housing. Over time, the plastic tabs that hold the filter in place can crack from repeated removal, or the screen itself can warp from heat exposure. When that happens, you'll notice lint escaping around the edges or the filter won't stay seated during operation. This replacement supersedes the earlier DC97-16013B part number and fits identically.

Compatible Samsung & Kenmore Models

This lint filter assembly works across Samsung's DV200, DV300, DV400, and DV500 dryer series. Here are the most common models:

• DV210AEW/XAA — Samsung electric dryer, white
• DV220AEW/XAA — Samsung electric dryer with steam
• DV330AEW/XAA — Samsung large-capacity electric
• DV330AGW/XAA — Samsung large-capacity gas
• DV331AER/XAA — Samsung electric dryer, red finish
• DV331AEW/XAA — Samsung electric dryer, white
• DV337AEG/XAA — Samsung electric dryer, granite finish
• DV337AEL/XAA — Samsung electric dryer, blue finish
• DV393ETPARA/A1 — Samsung electric dryer with touchscreen
• DV393GTPARA/A1 — Samsung gas dryer with touchscreen
• DV395ETPARA/A1 — Samsung electric dryer, premium series
• DV405ETPASU/A1 — Samsung electric dryer with stainless drum
• DV419AEU/XAA — Samsung electric dryer, platinum finish
• DV431AEP/XAA — Samsung electric dryer, onyx finish
• DV438AEL/XAA — Samsung electric dryer, blue wave finish
• DV448AEE/XAA — Samsung electric dryer with moisture sensor
• DV456EWHDWR/AA — Samsung electric dryer, white with reversible door
• DV484ETHASU/AA — Samsung electric dryer, 8.0 cu ft
• DV520AEP/XAA — Samsung electric dryer, premium platinum
• Kenmore 796.8137# — Kenmore Elite dryers built by Samsung

Why This Part Fails

Lint filters take a beating. You're pulling them out after every load, and that constant sliding action wears down the plastic guide rails inside the housing. The screen mesh itself is fine-gauge metal that can develop tears if you're not gentle when cleaning it — and once there's a hole, lint starts getting through. The bigger problem is heat degradation. If your dryer's been running hot due to a clogged exhaust vent, that filter housing can warp just enough that it no longer creates a tight seal. When that happens, you'll see lint accumulating inside the dryer cabinet or clinging to clothes after the cycle finishes.

Installation Overview

Replacing the lint filter is literally a slide-in, slide-out operation — no tools required. Pull the old filter straight out from the lint trap opening at the top of the dryer door. Slide the new DC97-16013A assembly straight in until it seats flush. That's it. The real work here is making sure you've addressed why the old one failed. If your exhaust vent is clogged, the new filter will fail just as fast. Take the opportunity to disconnect and clean your entire vent run from the dryer to the exterior termination before installing the new filter.

Part Specifications

What's Included

You're getting the complete assembly — the plastic housing with integrated handle and the lint screen already installed. This is a direct OEM replacement, so fitment is exact. No modifications, no adapters, no fussing with it to make it work.

Maintenance Tips

Clean your lint filter before every load — that's not optional. Pull it out, peel off the lint layer, and slide it back in. Once a month, wash the screen with warm soapy water to remove the fabric softener residue that clogs the mesh and restricts airflow. Let it dry completely before reinstalling. And at least twice a year, pull your dryer away from the wall and disconnect the exhaust vent to clean it thoroughly. A clogged vent is the number one reason dryers overheat and lint filters fail prematurely.

Order Your Replacement

The DC97-16013A is in stock and ships same-day from our warehouse. We're shipping the current OEM version that supersedes the older DC97-16013B — same part, updated packaging. If you're unsure about compatibility, call our parts team with your model number and we'll verify fitment before you order.