Samsung Dryer Door Switch Parts — Models & Compatibility

Your Samsung dryer won't start even though you've closed the door firmly. You hear nothing when you press the start button, or the drum won't turn despite power flowing to the unit. That's the door switch failing — a small but critical safety component that tells your dryer it's safe to operate. This hub covers the DC64-00828B door switch replacement compatible with dozens of Samsung and Kenmore dryer models, primarily in the DV series lineup.
Is This the Right Part for Your Model?
Before ordering, you'll need to verify your exact model number. On Samsung dryers, look for the rating plate inside the door opening on the front panel rim, or check the back panel near the power cord. The model number typically starts with "DV" followed by numbers and letters — like DV511AEW, DV520AGW/XAA, or DV42H5400EW. Cross-reference your full model number against the compatibility list below. The DC64-00828B replaces the older DC64-00828A version and supersedes part numbers AP4578931, PS4210965, and 2071595.
About This Replacement Part
The door switch (also called a door latch switch) is a simple push-button mechanism mounted in the door frame. When you close the dryer door, the door strike presses this switch closed, completing an electrical circuit that signals the control board it's safe to start. Over time, the internal contacts wear down from thousands of cycles, causing intermittent operation or complete failure. You might notice the dryer stopping mid-cycle when the door is still closed, or refusing to start at all. The DC64-00828B is a direct-fit replacement that mounts with two screws and connects via a wire harness plug — no modifications needed. This part works across both electric and gas Samsung dryer models, as the door switch operates independently of the heating system.
Compatible Samsung & Kenmore Models
This door switch fits a wide range of Samsung dryer models manufactured from approximately 2010 through 2020, including both front-load and side-opening designs. The part is identical across electric and gas variants within the same model series.
DV500 Series
- DV501AEW
- DV511AEW
- DV511AGR
- DV520AEP
- DV520AGW/XAA
- DV520AEW/XAA
DV400 Series
- DV433GTGJWR
- DV476GTHAWR
- DV484GTHASU
- DV42H5400EW
- DV45K6500EV
High-Efficiency Models
- DV50F9A6GVW
- DV50F9A8GVPA2
- DV50F9A8GVWA2
- DVE45R6300V
Note: If your model number includes suffixes like /XAA, /XAC, or color codes, the base model number determines compatibility. This list represents common models — the DC64-00828B fits many additional DV-series Samsung dryers not shown here.
What You're Getting
The DC64-00828B replacement includes the complete door switch assembly with mounting bracket and pre-attached wire connector. You don't need to transfer any parts from your old switch — just remove the two mounting screws, unplug the wire harness, and reverse the process with the new switch. The part arrives ready to install with no additional hardware required.
How to Verify Your Door Switch Has Failed
A failed door switch shows consistent symptoms. With the door closed, press the start button — if nothing happens (no lights, no sounds, no drum movement), but the dryer works fine with the door held slightly open, the switch contacts are likely stuck open. You can test this by manually pressing the switch plunger with a screwdriver while the door is open. If the dryer starts when you press the plunger, the switch needs replacement. Another test: with the dryer unplugged, use a multimeter set to continuity mode. Disconnect the switch wires, press the plunger, and test across the two terminals — you should see continuity (beep) when pressed, and no continuity when released.
Installation Overview
Replacing the door switch takes about 15 minutes with basic tools. You'll need a Phillips screwdriver and possibly a flathead for prying trim panels. Unplug the dryer first. Open the door and locate the switch assembly in the door frame — it's usually on the right side near the latch mechanism. Remove the two mounting screws, pull the switch forward, and disconnect the wire harness by pressing the locking tab. Install the new switch in reverse order, ensuring the plunger aligns properly with the door strike plate. Test by closing the door and attempting to start a cycle before pushing the dryer back into place.
Cross-Reference Numbers
If you're finding this part through other sources, it may be listed under these alternate numbers:
- AP4578931
- PS4210965
- DC64-00828A (older version)
- 2071595
All these numbers reference the same replacement part. The DC64-00828B is the current Samsung part number and supersedes the earlier DC64-00828A design.
Can't find your model?
Enter your model number and we'll confirm the right part.