LG & Kenmore Washer Water Level Pressure Switch Parts — Models & Compatibility

Your LG or Kenmore top-load washer won't fill properly, or it overfills and floods — that's usually your water level pressure switch giving out. This hub covers the 6501EA1001R pressure switch that works across 50+ LG and Kenmore washer models from the WT1101CW through WT7600HK series. If you've got an LG washer that's acting confused about how much water it needs, you're in the right place.

Is This the Right Part for Your Model?

Check your washer's model number before ordering. On LG top-loaders, you'll find it on a metal tag inside the lid opening, usually on the right side. Match your exact model number against the compatibility list below — this switch fits over 50 models including the WT1101CW, WT5101HW, WT7200CW, and most models between 2010-2016.

About This Replacement Part

The water level pressure switch (part number 6501EA1001R) tells your washer's control board when to stop filling water. It works through air pressure — as water fills the tub, air pressure builds in a connected tube, and when it hits the right level, the switch signals the board to shut off the fill valve. This part replaces older numbers AP5204365, 6501EA1001C, EBF62754506, and 2651052. When it fails, you'll see washers that keep filling until they overflow, or won't fill enough water to wash properly. Some machines throw error codes, others just behave erratically. The switch assembly mounts near the top of the cabinet, usually on the right side, with a clear air tube running down to the tub. It's a straightforward swap once you've unplugged the machine and removed the control panel or top cabinet section to access it.

Compatible LG & Kenmore Washer Models

This pressure switch works across multiple LG washer series. Verify your exact model number before purchasing:

• WT1101CW, WT1201CV, WT1201CW, WT1501CW — Early top-load series
• WT1701CV, WT1701CW, WT1801HVA, WT1801HWA — Mid-capacity models
• WT4870CW, WT4970CW, WT5001CW, WT5070CW — Standard capacity series
• WT5101HV, WT5101HW, WT5170HV, WT5170HW — High-efficiency models
• WT5270CW, WT5480CW, WT5680HVA, WT5680HWA — Large capacity series
• WT6001HV, WT6001HW, WT7200CW, WT7500CW, WT7600HK — Premium capacity models

Installation Overview

Replacing the pressure switch requires accessing the top cabinet area of your washer. You'll need to unplug the machine, remove the control panel screws (usually two at the back), and tilt the panel forward. The switch sits on the right side of the cabinet in most models. Disconnect the wire harness, remove the air tube carefully (don't tear it), unbolt the old switch, and reverse the process with the new one. Make sure that air tube connection is secure — a loose tube causes the same symptoms as a bad switch.

Why This Part Fails

Pressure switches wear out from constant cycling. Every wash cycle activates the switch multiple times as the washer fills, drains, and refills for rinse cycles. After years of use, the internal contacts corrode or the diaphragm that senses pressure develops cracks. Hard water deposits can also clog the air tube or pressure port on the switch itself. If your washer has started overfilling in the past few months, or you're getting inconsistent water levels between cycles, the switch has likely reached end of life.

Order Your Replacement Switch

The 6501EA1001R water level pressure switch costs $59.99 and ships ready to install. It's the exact replacement for AP5204365, 6501EA1001C, EBF62754506, and 2651052. Verify your model number, order the part, and you'll have your LG or Kenmore washer filling properly again within 30 minutes of opening the box.