Whirlpool & Maytag Gas Dryer Valve Coil Parts — Models & Compatibility

When your gas dryer fires up but the flame dies after a few seconds, you're likely dealing with a failed gas valve coil. This hub covers the W10328463 gas valve coil kit that fits dozens of Whirlpool, Maytag, Amana, and Kenmore gas dryers. It's one of the most common heating failures in these models, and thankfully, one of the easiest fixes.

Is This the Right Part for Your Model?

Check your dryer's model number before ordering. You'll find it on a sticker inside the door opening or on the back panel near the power cord. This coil kit fits models starting with WGD (Whirlpool gas dryers) and MGD (Maytag gas dryers) across multiple generations. Cross-reference your full model number with our compatibility list below — if your model starts with WGD4815, WGD5000, WGD94HE, MGDC465, or MGDC215, you're in the right place.

About This Replacement Part

Gas valve coils are electromagnetic devices that control gas flow to your dryer's burner assembly. When they fail, the dryer will run but won't heat — or the burner lights briefly before shutting off. One customer described it perfectly: "Gas dryer stopped heating." Another troubleshot with a multimeter, replaced the coil, and reported the dryer "working better than I EVER remember."

This kit includes both coils needed for most Whirlpool and Maytag gas valve assemblies. The repair typically takes 15-30 minutes with basic tools: nut drivers, screwdrivers, and an adjustable wrench. You'll need to disconnect the gas line (use a wrench to loosen the fitting), remove the front panel or top access, and swap the coils on the valve body. It's rated as an easy repair even for first-timers.

Common Symptoms

• Dryer won't heat at all
• Flame ignites then shuts off after a few seconds
• Burner cycles on and off repeatedly
• Gas smell when dryer runs (coils not opening valve properly)

What's Included

The W10328463 kit contains both the holding coil and the opening coil needed for a complete gas valve repair. It replaces part numbers WPW10328463, AP6019658, W10273784, W10295524, and W10311021. This is the same OEM-quality part pro techs install, not a flimsy aftermarket knockoff.

Tools You'll Need

• 1/4" and 5/16" nut drivers
• Phillips and flathead screwdrivers
• Adjustable wrench (for gas line connection)
• Socket set (optional, for some models)
• Pliers

Turn off the gas supply and unplug the dryer before starting any repair. If you're not comfortable working with gas connections, call a pro — but most DIYers handle this repair without issue.

Compatible Whirlpool Models

This gas valve coil kit fits the following Whirlpool gas dryer models. Check your exact model number to confirm compatibility:

• WGD4815EW2
• WGD5000DW
• WGD94HEAW0
• WGD49STBW2
• WGD4975EW0
• WGD8620HW1
• WGD87HEDW0
• WGD560LHW1
• 7MWGD9270XR1
• 7MWGD9270XL1
• WGD9620HBK0

Compatible Maytag Models

Maytag gas dryers using this same coil kit include:

• MGDC465HW
• MGDC215EW

Installation Overview

The basic process: unplug the dryer, shut off the gas, disconnect the gas line at the valve, remove access panels to reach the gas valve assembly, note the wire connections on the old coils (take a photo), slide off the old coils, install the new ones in the same positions, reconnect wires, reattach gas line, turn on gas, check for leaks with soapy water, and test the dryer.

Most failures happen because the coil windings break down over time from heat cycling. You'll know it's the coils if the igniter glows orange but the gas doesn't stay flowing. That's the holding coil failing to keep the valve open after the opening coil does its job.

Why This Part Fails

Gas valve coils sit right next to the burner assembly where temperatures fluctuate constantly. After thousands of heating cycles, the electromagnetic coil windings degrade. The opening coil might still work (you'll see a brief flame), but the holding coil fails to maintain gas flow. It's a wear-and-tear part, not usually caused by user error or electrical problems.

Troubleshooting Tips

Before replacing the coils, verify they're actually the problem. Use a multimeter to test resistance — good coils typically read between 1000-2000 ohms. If you're getting zero or infinite resistance, the coil is shot. Also check that your thermal fuse hasn't blown (common issue that mimics coil failure). The thermal fuse is usually mounted on the blower housing and requires continuity to work properly.

Order Information

Part number W10328463 typically ships same-day if ordered before 3 PM EST. Price is $61.99, which is significantly less than a service call. The part comes with a manufacturer warranty and fits as a direct replacement — no modifications needed.