Whirlpool & Kenmore Freezer Evaporator Fan Motor Parts — Models & Compatibility

If your Whirlpool or Kenmore refrigerator's freezer section isn't staying cold — or you're hearing grinding noises from behind the back panel — there's a good chance it's the evaporator fan motor. This motor circulates cold air from the evaporator coils throughout both the freezer and fridge compartments. When it fails, temperatures rise fast.

This hub covers the 2315539 evaporator fan motor, which fits over 50 Whirlpool, Kenmore, Maytag, and KitchenAid models. It replaces part numbers WP2315539, W10438708, 2219689, 2225625, and AP6007247.

Is This the Right Part for Your Model?

Check your model number against the compatibility list below. You'll find it on a sticker inside the fridge compartment — usually on the left wall near the top, or on the ceiling. Write down the full model number including letters and numbers.

Common compatible series include WRT, ET1, ET4, GT1, and M1TX models for Whirlpool, plus Kenmore 106-series side-by-sides and top-freezers. If your model starts with these prefixes and you're experiencing warm temps or fan noise, this is likely your part.

About This Replacement Evaporator Fan Motor

The evaporator fan motor sits behind the freezer's back panel, mounted directly to the evaporator coils. Its job is simple but critical: pull air across the cold coils and push it through vents into both compartments. When this motor dies, cold air stops moving — even though the compressor keeps running.

Most common failure symptoms: freezer section too warm while compressor runs continuously, fridge compartment warming up within 24 hours, or loud grinding/squealing noises from the freezer. Some owners notice frost buildup on the back panel because airflow has stopped. The motor itself typically fails due to bearing wear after years of constant operation, though power surges can also burn out the windings.

This direct replacement motor includes mounting brackets and fits the same mounting holes as your original. It's rated for the same voltage and RPM as OEM Whirlpool parts. Installation requires removing the freezer's contents, unscrewing the back panel, disconnecting the wire harness, and swapping the motor — usually about 30-45 minutes if you've done appliance repairs before.

What Customers Say

Owners who've installed this motor report immediate results. One Whirlpool owner wrote: "Great service and high quality product!" Another simply noted: "Great!" — short reviews, but they confirm the part works as expected once installed.

Compatible Models

This evaporator fan motor fits the following Whirlpool, Kenmore, Maytag, and KitchenAid models. If you don't see your exact model listed, check for similar prefix patterns — these manufacturers often use the same fan motor across multiple series:

• WRT318FMDW01 (Whirlpool top-freezer)
• WRT371SZBM01 (Whirlpool top-freezer)
• WRT108FZDM00 (Whirlpool top-freezer)
• WRT348FMES05 (Whirlpool top-freezer)
• WRTX5328PB01 (Whirlpool top-freezer)
• GT1SHTXMB00 (Whirlpool top-freezer)
• ET4CSKYKQ01 (Whirlpool top-freezer)
• ET1CHEXVB00 (Whirlpool top-freezer)
• 8ET1FTKXKT05 (Whirlpool top-freezer)
• 8ET1MTKXKT02 (Whirlpool top-freezer)
• 8ET8FTKXKT03 (Whirlpool top-freezer)
• M1TXEMMWW00 (Whirlpool top-freezer)
• 106.60219410 (Kenmore top-freezer)

Note: This is a sample of compatible models. The full list includes 50+ models across multiple brands. If your model number starts with WRT, ET1, ET4, GT1, M1TX, or Kenmore 106-series, check the full compatibility chart on the product page.

Installation Quick Guide

You'll need a Phillips screwdriver and a 1/4" nut driver. Unplug the fridge completely before starting — this motor connects directly to the main power circuit. Remove all freezer shelves and baskets for access to the back panel screws. The fan motor mounts with two screws and connects via a two-wire harness. Reverse the process with the new motor, ensuring the fan blade spins freely before reassembling.

Pricing & Availability

The 2315539 evaporator fan motor is priced at $51.99 — significantly less than a service call. Most OEM and aftermarket versions of this motor fall in the $45-$65 range. Given that a technician will charge $150-$200 just for the diagnosis visit, this is a straightforward DIY repair that pays for itself immediately.