Whirlpool Washer Drain Pump Parts — Models & Compatibility

Your Whirlpool front-load washer's drain pump assembly does one critical job: remove water after each cycle. When it fails, you're left with standing water, wet clothes, and a machine that won't advance to the spin cycle. This hub covers the W10130913 drain pump assembly that fits over 20 Whirlpool, Maytag, Kenmore, Amana, and Inglis washer models.

Is This the Right Part for Your Model?

Before ordering, you'll need your washer's exact model number. On front-load Whirlpool washers, look inside the door frame along the top edge or check the back panel near the water inlet connections. The model number typically starts with "WFW" followed by four digits. Cross-reference your model with the compatibility list below — this pump assembly replaces part numbers WPW10730972, 8540024, W10730972, W10117829, and AP6023956.

About This Replacement Drain Pump

The W10130913 is an OEM-equivalent drain pump assembly designed for Whirlpool's front-load washer series, particularly the WFW8400, WFW8300, WFW8410, WFW8500, and WFW9050 model families. This pump handles both draining water during the cycle and the final spin evacuation. Common failure symptoms include water not draining completely, leaking from the pump housing, a burning smell during drain cycles, or the washer refusing to start because it detects standing water. Some owners report the pump motor running but not moving water — typically caused by a jammed impeller or failed motor windings. The complete assembly includes the motor, pump housing, and mounting bracket, so you're not piecing together multiple components.

Compatible Whirlpool Washer Models

This drain pump assembly fits the following Whirlpool model series. If your model number isn't listed but starts with the same prefix, check the full compatibility chart on the product page:

• WFW8400TW Series: WFW8400TW00, WFW8400TW01, WFW8400TW02
• WFW8300SW Series: WFW8300SW03, WFW8300SW04, WFW8300SW05
• WFW8410SW Series: WFW8410SW02, WFW8410SW03
• WFW8500SR Series: WFW8500SR01, WFW8500SR02, WFW8500SR03
• WFW9050XW Series: WFW9050XW01, WFW9050XW02, WFW9050XW03

This pump also works with equivalent Maytag, Kenmore, Amana, and Inglis models that share the same platform. Always verify your model number before purchasing.

What Causes Drain Pump Failure?

Drain pumps fail for predictable reasons. Small objects like coins, hairpins, or fabric fragments get past the filter and jam the impeller. Over time, detergent residue builds up inside the pump housing, creating friction that burns out the motor. Hard water deposits can seize the impeller shaft. And because the pump runs under load during every cycle, the motor windings eventually fail after years of use. If you're hearing a humming sound but no water movement, the motor's trying to spin a jammed or seized impeller. A burning smell means the motor's overheating — shut it down immediately to prevent electrical damage to the control board.

Installation Overview

Replacing the drain pump requires accessing the washer's underside or front panel, depending on your model. You'll disconnect the drain hose, inlet hoses, and wire harness from the old pump, then transfer them to the new assembly. The pump mounts with three or four screws to the washer tub. Most DIYers complete this in 30-45 minutes with basic hand tools. Run a drain cycle after installation to check for leaks at the hose connections.

Frequently Asked Questions

Will this pump work with Maytag or Kenmore washers?

Yes, if they share the same platform as these Whirlpool models. Maytag and Kenmore front-loaders built during the same production years often use identical drain pump assemblies. Check your model's parts diagram to confirm.

Do I need to replace the drain hose at the same time?

Not unless the hose shows cracks, kinks, or blockages. Inspect it while you've got the pump out — if it's clogged with lint or detergent buildup, clean it thoroughly or replace it to prevent future drainage problems.

What if the new pump arrives and doesn't fit?

Double-check your model number against the compatibility list. If you've confirmed compatibility and the part still doesn't match, contact customer service with photos of your original pump and model tag. Part mix-ups happen occasionally, and they'll ship the correct assembly once verified.

Order Your Replacement Drain Pump

The W10130913 drain pump assembly is in stock at $92.99 with shipping available to all 50 states. Orders placed before 2 PM EST typically ship same-day. You're getting an OEM-equivalent part with the same specifications as the factory original, backed by a standard warranty.