Samsung Dryer Lint Filter Case Parts — Models & Compatibility

The lint filter case in Samsung dryers takes a beating. Every load cycle means the filter gets pulled out, cleaned, and shoved back in — eventually the housing cracks, the clips break, or the seal warps. When that happens, lint bypasses the filter and builds up inside the dryer cabinet, which is a fire hazard waiting to happen. This guide covers DC61-02595A compatibility across Samsung's front-load and top-load dryer models from 2010 through 2016.

Is This the Right Part for Your Model?

Samsung model numbers are stamped on a label inside the dryer door frame or on the back panel near the power cord. You're looking for something like DV42H5200EW/A3 or DV520AEW/XAA. The crucial part is the base model number (before the slash) — the suffix tells you the production revision, but DC61-02595A fits across multiple revisions of the same base model.

This lint filter case fits both electric and gas versions of Samsung's mid-tier dryer lineup. If your model starts with DV42H, DV45H, DV48H, or DV52, you're in the right place. Check the full compatibility list below to confirm your exact model.

About This Replacement Part

DC61-02595A is the complete lint filter housing assembly — it includes the outer case, the mounting tabs, and the gasket that seals against the dryer drum. Samsung uses the same basic design across their 7.5 cu ft and 8.5 cu ft dryers, which is why one part number covers so many models. The assembly is gray plastic with a spring-loaded latch mechanism.

The most common failure mode is cracked mounting tabs. When you pull the lint screen out at an angle instead of straight, it puts stress on the plastic tabs that hold the case to the bulkhead. Over time, one tab cracks, then the case shifts, then the seal fails and lint escapes. You'll know the case needs replacing if the filter feels loose, if you can see cracks around the edges, or if you're finding excessive lint inside the drum area instead of on the filter itself.

Replacement takes about 15 minutes. You'll need to remove the top panel of the dryer to access the mounting screws from above. The case is held by four screws and one wire harness connector for the moisture sensor (on models that have one). The trickiest part is getting the gasket seated properly so it seals against the bulkhead — if it's not flush, you'll have the same lint bypass problem you started with.

Compatible Samsung Dryer Models

This part works across Samsung's DV42H, DV45H, DV48H, and DV52 series dryers. Both electric (E) and gas (G) versions use the same lint filter case design. Here are the confirmed compatible models:

• DV42H5200 Series: DV42H5200EW/A3, DV42H5200EP/A3, DV42H5200EF/A3, DV42H5200GW/A3, DV42H5200GP/A3, DV42H5200GF/A3
• DV42H5000 Series: DV42H5000EW/A3, DV42H5000GW/A3
• DV48H7400 Series: DV48H7400EW/A2, DV48H7400GP/A2
• DV45H7000 Series: DV45H7000EW/A2, DV45H7000GP/A2
• DV520A Series: DV520AEW/XAA, DV520AEP/XAA, DV520AGW/XAA
• DV511A Series: DV511AGR/XAA
• DV455EV Series: DV455EVGSGR/AA-02

If your model isn't listed but starts with DV42H, DV45H, DV48H, or DV52, cross-reference the part number on your existing lint filter case. Samsung consolidated parts across these series, so there's a good chance DC61-02595A will fit even if your specific revision isn't listed above.

Why This Part Fails

Samsung's lint filter design from this era has a known weak point. The case uses thin plastic mounting tabs instead of metal brackets, and those tabs sit right where users grab the filter to pull it out. Every time someone yanks the filter at an angle — which is natural when you're in a hurry — it flexes those tabs. After a few years of that stress, the plastic fatigues and cracks.

The other failure mode is UV damage if your dryer sits near a window. The gray plastic gets brittle from sunlight exposure, then cracks spontaneously even with normal use. If you notice the plastic looks chalky or faded, that's UV degradation and the case is living on borrowed time.

What Comes in the Box

You get the complete lint filter housing assembly, but the actual lint screen (the mesh part) is sold separately. If your lint screen is torn or warped, you'll need to order that as a separate part — it's usually DC97-16742A for these models. The case comes with the gasket pre-installed, but double-check that it's seated correctly before you mount it.

Installation Quick Reference

Here's the basic procedure: unplug the dryer, remove the top panel (two screws at the back corners), disconnect the moisture sensor wire if present, remove four mounting screws holding the old case, lift out the old case, position the new case and verify the gasket is flush, reinstall the four screws, reconnect the moisture sensor, test-fit the lint screen, replace the top panel. Run a test cycle and check for lint accumulation in the drum area — if you see lint escaping, the gasket isn't seated right and you need to reseat the case.