Frigidaire Washer Door Striker Parts — Models & Compatibility

Your Frigidaire front-load washer won't start, and you've triple-checked that the door is closed. The problem? A worn or damaged door striker that prevents the latch actuator from engaging properly. This small but critical part — the 131763302 door striker — is what tells your washer it's safe to start the wash cycle. When it fails, your machine sits idle no matter how many times you slam the door shut.

This hub covers the 131763302 door striker replacement for Frigidaire, Electrolux, Crosley, and Kenmore front-load washers. We'll show you which models use this part, how to verify compatibility, and what you need to know before ordering.

Is This the Right Part for Your Model?

The 131763302 striker fits primarily Frigidaire and Electrolux-manufactured front-load washers from the ATF and BKFW series, along with select Kenmore models. Your model number is typically located on a sticker inside the door frame or along the top edge when you open the door. Write down the full model number including any letters and numbers after the dash.

Cross-reference your model number against the compatibility list below. If your model isn't listed but starts with ATF, BKFW, or similar prefixes, there's a good chance this striker will work — Frigidaire used this same part across multiple series during the 2000s and 2010s.

About This Replacement Part

The door striker is the plastic catch mounted on the washer door that engages with the door lock actuator on the washer frame. If the actuator is damaged, the door will not latch properly and the washer will not turn on. You'll hear a clicking sound when you close the door, but the control panel won't respond and the cycle won't start.

Common failure symptoms include the washer refusing to start even though the door appears closed, error codes related to door lock failure, or the door bouncing back open slightly after you close it. The striker itself can crack from repeated use, wear down from friction, or break off entirely if someone pulls the door open while it's locked mid-cycle.

This replacement striker (part number 131763302) supersedes older part numbers 134456640, 134456602, and AP4508273. If you've found any of those numbers in your parts search, this is the updated version you need. Installation takes about 10 minutes with a Phillips screwdriver — you'll remove the door panel, swap out the old striker, and reassemble.

Compatible Model Series

This door striker fits over 20 Frigidaire-manufactured washer models, primarily in the ATF series (Affinity line) and select Kenmore front-loaders built by Frigidaire. The most common series include:

• ATF6500 Series: Basic Affinity models with 3.4 cu ft capacity
• ATF6700 Series: Mid-range Affinity with steam options
• ATF7000 Series: Larger capacity Affinity washers
• ATF8000 Series: Premium Affinity models
• BKFW Series: Builder's package Kenmore models

If you've got an Affinity washer manufactured between 2005 and 2015, chances are excellent this is your part. The door striker design remained consistent across these model years, which is why one part number covers so many machines.

What You're Getting

The 131763302 is the complete door striker assembly — the white or gray plastic catch that mounts to your washer door. It includes the mounting holes and striker post that engages with the lock mechanism. You're not getting screws with this part, but you can reuse the screws from your old striker.

This is an OEM-equivalent replacement that matches the original Frigidaire part specifications. The striker material is reinforced plastic designed to withstand thousands of door closures without cracking or wearing down prematurely.

Installation Overview

Replacing the door striker requires removing the door's inner panel to access the mounting screws. You'll disconnect the door from the washer (two bolts at the hinges), remove the screws around the door's perimeter to separate the inner panel, swap the striker, and reassemble. The trickiest part is lining up the door panel screws on reassembly — work slowly and make sure the door gasket seats properly before tightening everything down.

Test the repair by closing the door and listening for a solid click. The control panel should light up normally, and you should be able to start a cycle. If the door still won't latch, check the actuator on the washer frame side — it might need replacement as well.

Frequently Asked Questions

Will this fix a door that won't lock?

It depends. If the striker itself is cracked or broken, yes — this replacement will solve your problem. But if the door lock actuator (the part mounted on the washer frame) is faulty, you'll need to replace that component instead. Inspect both parts before ordering.

Can I use this on an Electrolux washer?

Yes, many Electrolux front-load washers use the same door striker design as Frigidaire models. Check your model number against the compatibility list — Electrolux-branded machines manufactured by Frigidaire will show up as compatible.

Is this part covered under warranty?

That depends on your washer's age and original warranty terms. Most Frigidaire washers come with a one-year parts and labor warranty, with extended coverage on certain components. If your washer is under warranty, contact Frigidaire before ordering parts yourself — unauthorized repairs can void coverage.